Wholesale 1060 H112 Hot Rolled Aluminum: Mga gidak-on, Properties ug Supply

Pasiuna

Buyers looking for wholesale 1060 H112 hot rolled aluminum are usually sourcing thick, mill-finish plate or hot rolled coil in volume—as welded tank and lining plate, anti-corrosion equipment, general fabrication stock or feedstock for cold rolling.

1060 is a commercially pure aluminum (pinakagamay 99.60% Si Al), and the H112 temper identifies plate produced by hot rolling with guaranteed minimum mechanical properties.

Hot rolled H112 plate is the most economical way to buy 1060 in medium and heavy gauges: it is soft and ductile, resistensya sa korosion, easy to weld and machine, and available in large widths and lengths.

This guide explains the H112 temper, how hot rolled differs from cold rolled, the composition and properties, standard sizes and weights, mga aplikasyon, and how to order wholesale factory-direct.

What Does the H112 Temper Mean?

H112 is an “as-fabricated” temper for products shaped by hot working. Its key points are:

• The plate obtains its strength from the hot rolling process rather than controlled cold work.
• The exact degree of strain hardening is not controlled, but the standard sets guaranteed minimum mechanical properties.
• It is typically used for thicker plate (from about 6 mm upward) supplied straight from hot rolling with only leveling.
• Because it is not deliberately cold-hardened, H112 stays ductile and weldable and is well suited to later forming, machining or further processing.

For comparison, F is the fully free as-fabricated state with no property guarantees, H111 is annealed with only light hardening from leveling, and the H1x/H2x tempers are cold-rolled conditions.

H112 sits between them: hot worked, yet certified to minimum strength and elongation.

Hot rolling is especially well matched to pure aluminum: worked above its recrystallization temperature, the metal flows without the large residual stresses and edge cracking that hard cold work can cause in thick sections,

and the continuously recrystallized grain keeps the plate isotropic and easy to weld or machine.

After leveling it leaves the mill essentially stress-relieved and flat, which is why fabricators prefer H112 for large welded structures that must stay dimensionally stable rather than distort after cutting.

Hot Rolled vs Cold Rolled Aluminum

	Init nga giligid (H112)	Bugnaw nga giligid
Proseso	rolled above the recrystallization temperature	rolled at room temperature
Gibag-on	medium and heavy plate, typically about 6–300 mm+	thin sheet and foil, below about 6 mm
Nawong	dark/bright mill finish, slightly less smooth	hamis, hayag, tight-tolerance surface
Mga kabtangan	humok, ductile, low residual stress; cold-rolling feedstock	harder or precision tempers (O/H14/H18)
Presyohan	lower per kg in heavy gauges	higher processing cost for thin/bright product

 

Choose hot rolled H112 when thickness, price, weldability or later processing dominates and a polished surface is not required; choose cold rolled for thin gauges, bright finishes or precise hardness.

Kemikal nga Komposisyon ug Mekanikal nga Properties

elemento	Si Al	Ug	Si Fe	Cu	Mn	Si Mg	Zn
1060	≥99.60	≤0.25	≤0.35	≤0.05	≤0.03	≤0.03	≤0.05

 

Minimum H112 properties fall slightly with very heavy section (alang sa GB / T 3880); note that some online listings wrongly quote steel-like 300–800 MPa values for 1060, which are impossible for pure aluminum and should be ignored:

Gibag-on (mm)	Kusog sa tensile (aga)	Elongation (aga)
>4.5–6	75 MPa	10%
>6–12.5	75 MPa	10%
>12.5–40	70 MPa	18%
>40–80	60 MPa	22%

 

Density is about 2.71 g/cm³; thermal conductivity is high and weldability is excellent. Confirm the guaranteed values for your thickness on the mill test certificate.

Standard Sizes and Plate Weight

1060 H112 hot rolled plate is supplied from about 6 mm to 200–300 mm (heavier on request), in widths up to roughly 2600–5000 mm and lengths to about 12,000–13,000 mm, cut to standard or custom dimensions. Weight per m² = thickness (mm) × 2.71; a 4×8 ft sheet covers 2.972 m².

Gibag-on	kg/m²	Timbang matag 4 × 8 sheet
6 mm	16.3	bitik. 48.3 kg
8 mm	21.7	bitik. 64.4 kg
10 mm	27.1	bitik. 80.5 kg
20 mm	54.2	bitik. 161 kg
50 mm	135.5	bitik. 403 kg
100 mm	271	bitik. 805 kg

Kinaandan nga mga Aplikasyon

• Welded storage tanks, boiler and tank lining plates and large anti-corrosion equipment cabinets.
• Chemical process equipment, vessels, pipes and fittings in mild, non-structural service.
• Kinatibuk-ang katha, makina nga mga bahin, tooling blanks and spun or stamped components.
• Hot rolled coil as feedstock for cold rolling, fin stock or further finishing.
• Insulation jacketing and cladding where a heavy or wide mill-finish sheet is acceptable.

Because pure 1060 is low strength, do not use H112 plate for high-load or wear parts; pagpili 3003 for tougher cladding, 5052 for corrosion with strength, 5083 for marine/structural plate or 6061 for machined structural components.

Wholesale Supply, Quality Control and Ordering

A wholesale order can specify thickness and tolerance, width and cut length, plate or coil, edge type (slit or sawn), surface and any protective film, plus pagputol, buyog, drilling o CNC blangko sa drawing.

Ang mga galingan nagkupot ug dagkong rolling stocks sa komon nga mga gauge para sa paspas nga pagpadala sa bug-os nga trak o sudlanan nga gidaghanon, nga adunay mas gamay nga trial lot nga magamit.

Ang pagkontrol sa kalidad naglangkob sa gibag-on, gilapdon/gitas-on ug diagonal tolerance, patag, kalidad sa nawong ug tensile/elongation pinaagi sa gibag-on sa MTC; ISO 9001 gisuportahan sa mga galingan ang SGS/BV/TUV inspeksyon.

Ang plato giputos sa mga kahoy nga pallets o sa kahoy nga mga kaso nga adunay moisture-proof wrapping alang sa eksport. Ang presyo nagsunod sa aluminum ingot base ug bayad sa pagproseso, so compare per ton and per cut plate on identical gauge, size and Incoterm (FOB/CFR/CIF; kasagaran 30% deposit, balance against the bill of lading).

To quote, send alloy/temper (1060 H112), kabaga, width and length, plate or coil, kadaghanon, application and destination port.

For wholesale buyers, a direct mill relationship matters more than the lowest single quote: only a mill with hot-rolling capacity can hold thickness and flatness across container lots, supply consistent MTC values and replenish the same gauge month after month.

Confirm genuine capacity with a video of the hot line and the gauges actually rolled, run production-thickness samples through your cutting and welding operations, and use a signed sample as the receiving standard; traders reselling spot plate rarely match this consistency.

Kanunay nga gipangutana nga mga pangutana

Q: Unsa ang 1060 H112 hot rolled aluminum used for?

A: Welded tanks and lining plates, anti-corrosion and chemical equipment, kinatibuk-ang pagmugna, machined blanks, and hot rolled coil as cold-rolling feedstock, in medium and heavy gauges.

Q: What does H112 mean?

A: It is an as-fabricated, hot-rolled temper with guaranteed minimum mechanical properties but no controlled cold work, typically used for plate above about 6 mm.

Q: Why is some 1060 plate listed at 300-800 MPa?

A: Those figures are erroneous (often copied from steel listings); putli 1060 H112 has tensile minima of roughly 60–75 MPa depending on thickness, and such claims should be rejected.

Q: Hot rolled or cold rolled – which do I need?

A: Hot rolled H112 for thick, ekonomikanhon, weldable plate with a mill surface; cold rolled for thin gauges, bright finishes or controlled hardness.

Q: Can it be welded and cut to size?

A: Oo. 1060 H112 welds and machines easily and can be sawn, laser or plasma cut, bent and supplied as custom blanks with export packaging.

Q: What is the wholesale MOQ and lead time?

A: Wholesale is usually quoted per ton in full container/truck quantities, with trial orders negotiable; common gauges held in stock ship quickly and custom sizes depend on the mill schedule.

Panapos

Wholesale 1060 H112 hot rolled aluminum is the economical, ductile, weldable pure-aluminum plate for tanks, linings, anti-corrosion equipment, fabrication and cold-rolling feedstock in heavy gauges.

Specify thickness, width and length, buy on the guaranteed GB/T 3880 properties and mill certificates rather than inflated online strength claims, and compare like-for-like per ton under the same Incoterm.