1100 Aluminiumblech zu verkaufen: Noten, Größen und Kaufratgeber
1100 Aluminiumblech zu verkaufen: Noten, Größen und Kaufratgeber
Einführung
1100 aluminum sheet is one of the most practical commercially pure aluminum plates you can buy: with a minimum 99.0% aluminum content and a small copper addition, it is slightly stronger than 1050/1060 while keeping excellent formability, Korrosionsbeständigkeit, weldability and thermal conductivity.
It is the default sheet for chemical equipment, cookware and deep-drawn parts, Temperatur fällt, signs and general fabrication that do not need high strength.
Offered factory-direct, 1100 sheet can be supplied in standard 4×8 ft and metric sizes or cut to your dimensions, with the temper and surface finish the product needs.
This guide covers the composition, Eigenschaften, sizes and weights, Anwendungen, Herstellung, wie es im Vergleich dazu aussieht 1050, 1060 und 3003, und wie man bestellt.
Was ist 1100 Aluminiumblech?
1100 is a non-heat-treatable 1xxx-series alloy strengthened only by cold work and softened by annealing. Sheet generally runs about 0.2–6 mm thick (thicker material is plate), supplied flat or cut to length. Seine charakteristischen Vorteile sind:
- Hervorragende Duktilität beim Biegen, Stanzen, Spinnen und Tiefziehen, besonders im O-Temperament.
- Very good atmospheric and chemical corrosion resistance from the self-healing oxide film.
- Etwas höhere Festigkeit als 1050/1060 thanks to a controlled 0.05–0.20% copper addition.
- High thermal and electrical conductivity, plus excellent weldability and easy machining.
- Licht (um 2.71 g/cm³), rust-free and lower cost than alloyed grades; anodizes to a good film.
- The trade-off is modest strength; load-bearing or wear parts should use 3003, 5052 oder 6061.
Chemische Zusammensetzung und mechanische Eigenschaften
Die kontrollierte Chemie (per ASTM B209 / GB/T 3190) keeps silicon plus iron and copper within tight limits so forming, welding and corrosion performance stay high:
| Element | Al | Und + Fe | Cu | Mn | Zn |
| 1100 | ≥99,0 | ≤0,95 | 0.05–0,20 | ≤0,05 | ≤0,10 |
Mechanical properties change with temper, also das Gleiche 1100 Das Blech kann weich und tiefziehfähig oder hart und starr geliefert werden (typical Rm values):
| Temperament | Zug (MPa) | Charakter |
| DAS (geglüht) | ca.. 75–110 | Am weichsten; Tiefziehen, Spinnen, maximale Formbarkeit |
| H12 / H22 | ca.. 95–125 | Viertelhart; Lichtbildung |
| H14 / H24 | ca.. 110–150 | Halbhart; common general-purpose temper |
| H16 / H26 | ca.. 135–170 | Dreiviertelhart; steifere Platten |
| H18 | ca.. 150–200 | Vollhart; starr, begrenzte Formgebung |
Die Werte variieren geringfügig je nach Dicke und Standard; confirm tensile and yield on the mill certificate for your gauge.
The small copper addition is what distinguishes 1100 in service.
It gives a modest but useful gain in strength without sacrificing the pure-aluminum forming that lets the sheet be drawn into deep pots and liners, and the metal still anodizes into a uniform, protective film used on trim and nameplates.
1100 thus occupies a deliberate middle ground—not as soft and conductive as 1060, but not as alloyed as 3003, which is why it appears so often in cookware, chemical and general-purpose stock.
Standardgrößen, Oberflächen und Gewicht
1100 Blatt wird aus ca. hergestellt 0.2 zu 6 mm (Platte zu 200 mm+ auf Anfrage), in Breiten bis ca 2600 mm und Längen bis 12,000 mm. Common sizes include 4×8 ft (1219×2438), 1000×2000, 1220×2440, 1250×2500 and 1500×3000, plus custom blanks to drawing.
| Oberfläche / beenden | Typische Verwendung |
| Mühlenfinish (optional PVC/PVDF protective film) | Allgemeines Blatt, Fertigungsbestand, Verkleidung |
| Gebürstet / Spiegel | Dekorative Paneele, Typenschilder, Beleuchtung |
| Eloxiert / farbbeschichtet | Chemical and outdoor panels, durable signage, trimmen |
| Geprägt / circles | Isolierung, anti-slip, cookware discs and deep-drawn parts |
Weight is easy at 2.71 g/cm³: kg pro m² = Dicke (mm) × 2.71; a 4×8 ft sheet covers about 2.972 m².
| Dicke | kg/m² | Gewicht pro 4×8 Blatt |
| 0.5 mm | 1.36 | ca.. 4.0 kg |
| 1.0 mm | 2.71 | ca.. 8.1 kg |
| 1.5 mm | 4.07 | ca.. 12.1 kg |
| 2.0 mm | 5.42 | ca.. 16.1 kg |
| 3.0 mm | 8.13 | ca.. 24.2 kg |
Typische Anwendungen
- Chemische Prozessausrüstung, Lagertanks, Gefäße, pipes and fittings that need corrosion resistance and weldability.
- Kochgeschirr, cooking utensils and deep-drawn or spun parts, plus aluminum circles for pots and pans.
- Temperatur fällt, Lampenreflektoren, Vorrat an Flaschenverschlüssen, printing plates and food packaging components.
- Zeichen, nameplates and decorative or anodized architectural trim, and general stamped or bent parts.
Fabrication and Surface Treatment
1100 cuts, shears, bends and forms readily and can be laser, plasma or water-jet cut, gestempelt, spun and drilled; it welds cleanly by common processes and takes anodizing, Bürsten, polishing and coating well.
Use O temper for the deepest draws and harder tempers where the finished part must hold shape; generous bend radii and clean, oil-free surfaces help on high-speed lines.
1100 vs 1050, 1060 und 3003
| Grad | Mindest. Al / legieren | Stärke | Beste Passform |
| 1050 | 99.50% Al | Niedrig | Most economical general sheet and cladding |
| 1060 | 99.60% Al | Niedrig | Best conductivity/reflectivity; signs and electrical parts |
| 1100 | 99.00% Al, ein wenig Cu | Niedrig-mittel | Etwas stärker; Bildung, Schweißen, chemisch, Kochgeschirr |
| 3003 | Al + Mn (um 1.2%) | Medium | Um 20% stärker; Böden, tread, tougher cladding |
Wählen 1100 when you need a little more strength and weldability than 1050/1060 with the same pure-aluminum forming and corrosion; aufsteigen 3003 for real added strength.
Qualitätskontrolle, Pricing and How to Order
QC covers thickness and flatness, Breite/Länge und Diagonaltoleranz, surface quality and tensile/yield by temper and chemistry on the MTC; ISO 9001 mills support SGS/BV inspection.
Sheet is interleaved with protective film and packed on pallets or in cases with moisture-proof wrapping for export. Die Preise basieren auf der Basis von Aluminiumbarren zuzüglich einer Bearbeitungsgebühr, with thinner/wider gauge, individueller Zuschnitt, Oberflächenbehandlung und kleine Mengen erhöhen die Kosten;
compare per ton and per finished blank on identical specs under FOB/CFR/CIF (häufig 30% Kaution, Saldo gegen den Frachtbrief). Zitieren, Legierung/Vergütung senden (1100), Dicke, Blech- oder Rohlingsabmessungen, Oberfläche, Menge, Anwendung und Zielport.
Verify new material on production-gauge samples rather than photos: run the sheet through your forming, welding or cutting line at normal speed, Messen Sie die Dicke über die Breite, inspect the surface and, for food or chemical use, confirm the compliance paperwork matches the lot.
A signed pre-production sample then becomes the receiving standard, and an integrated mill that rolls and finishes in-house will hold that standard more reliably across repeat orders than spot resellers.
Häufig gestellte Fragen
Q: Was ist 1100 Aluminiumblech verwendet für?
EIN: Chemical tanks, vessels and piping, cookware and deep-drawn parts, Temperatur fällt, Zeichen, bottle cap and printing stock, and general fabrication needing formability and corrosion rather than high strength.
Q: Wie stark ist 1100 gegenüber 1060 und 3003?
EIN: It is slightly stronger than 1050/1060 due to a small copper addition, Aber 3003 (Mangan) is about 20% stärker; H18 1100 reaches roughly 150–200 MPa tensile.
Q: Welches Temperament soll ich wählen?
EIN: O for deep drawing and spinning, H14/H24 for general sheet, H16/H26 for stiffer panels and H18 for the most rigid plate with little forming.
Q: What sizes and thicknesses are available?
EIN: About 0.2–6 mm sheet in widths to roughly 2600 mm, einschließlich 4×8 Fuß und metrische Standards, with plate and cut-to-size blanks on request.
Q: Can it be welded, anodized and cut to size?
EIN: Yes—1100 welds cleanly, anodizes and finishes well, and can be laser or sawn cut, bent and supplied as custom blanks with protective film.
Q: Wie viel wiegt ein 4×8-Blatt??
EIN: Rund 8.1 kg bei 1 mm, 12.1 kg bei 1.5 mm, 16.1 kg bei 2 mm und 24.2 kg bei 3 mm, mit kg/m² = Dicke (mm) × 2.71 über 2.972 m².
Abschluss
1100 aluminum sheet is the slightly stronger, easy-to-fabricate pure-aluminum plate for chemical equipment, Kochgeschirr, heat transfer and signs.
Geben Sie den Härtegrad der Verarbeitung des Panels an, Dicke und Schnittgröße festlegen, choose the surface, und kaufen Sie auf Mühlenzertifikaten, Toleranzen und genehmigte Muster und nicht nur der Preis.
