Mórdhíola 1060 H112 Alúmanam Te Iarchurtha: Méideanna, Airíonna agus Soláthar

Tabhairt isteach

Buyers looking for wholesale 1060 H112 hot rolled aluminum are usually sourcing thick, mill-finish plate or hot rolled coil in volume—as welded tank and lining plate, anti-corrosion equipment, general fabrication stock or feedstock for cold rolling.

1060 is a commercially pure aluminum (íosta 99.60% Al), and the H112 temper identifies plate produced by hot rolling with guaranteed minimum mechanical properties.

Hot rolled H112 plate is the most economical way to buy 1060 in medium and heavy gauges: it is soft and ductile, resistant creimeadh, easy to weld and machine, and available in large widths and lengths.

This guide explains the H112 temper, how hot rolled differs from cold rolled, the composition and properties, méideanna caighdeánacha agus meáchain, iarratais, and how to order wholesale factory-direct.

What Does the H112 Temper Mean?

H112 is an “as-fabricated” temper for products shaped by hot working. Its key points are:

• The plate obtains its strength from the hot rolling process rather than controlled cold work.
• The exact degree of strain hardening is not controlled, but the standard sets guaranteed minimum mechanical properties.
• It is typically used for thicker plate (from about 6 mm upward) supplied straight from hot rolling with only leveling.
• Because it is not deliberately cold-hardened, H112 stays ductile and weldable and is well suited to later forming, machining or further processing.

For comparison, F is the fully free as-fabricated state with no property guarantees, H111 is annealed with only light hardening from leveling, and the H1x/H2x tempers are cold-rolled conditions.

H112 sits between them: hot worked, yet certified to minimum strength and elongation.

Hot rolling is especially well matched to pure aluminum: worked above its recrystallization temperature, the metal flows without the large residual stresses and edge cracking that hard cold work can cause in thick sections,

and the continuously recrystallized grain keeps the plate isotropic and easy to weld or machine.

After leveling it leaves the mill essentially stress-relieved and flat, which is why fabricators prefer H112 for large welded structures that must stay dimensionally stable rather than distort after cutting.

Hot Rolled vs Cold Rolled Aluminum

	Te rollta (H112)	Rolladh fuar
Próiseas	rolled above the recrystallization temperature	rolled at room temperature
Tiús	medium and heavy plate, typically about 6–300 mm+	thin sheet and foil, below about 6 mm
Dromchla	dark/bright mill finish, slightly less smooth	réidh, bright, tight-tolerance surface
Airíonna	bog, insínte, low residual stress; cold-rolling feedstock	harder or precision tempers (O/H14/H18)
Costas	lower per kg in heavy gauges	higher processing cost for thin/bright product

 

Choose hot rolled H112 when thickness, price, weldability or later processing dominates and a polished surface is not required; choose cold rolled for thin gauges, bright finishes or precise hardness.

Comhdhéanamh Ceimiceach agus Airíonna Meicniúla

Eilimint	Al	Agus	Fe	Cu	Mn	Mg	Zn
1060	≥99.60	≤0.25	≤0.35	≤0.05	≤0.03	≤0.03	≤0.05

 

Minimum H112 properties fall slightly with very heavy section (le haghaidh GB/T 3880); note that some online listings wrongly quote steel-like 300–800 MPa values for 1060, which are impossible for pure aluminum and should be ignored:

Tiús (mm)	Neart teanntachta (mí Miannach)	Fadú (mí Miannach)
>4.5–6	75 MPa	10%
>6–12.5	75 MPa	10%
>12.5–40	70 MPa	18%
>40–80	60 MPa	22%

 

Tá dlús thart 2.71 g/cm³; thermal conductivity is high and weldability is excellent. Confirm the guaranteed values for your thickness on the mill test certificate.

Standard Sizes and Plate Weight

1060 H112 hot rolled plate is supplied from about 6 mm to 200–300 mm (heavier on request), in widths up to roughly 2600–5000 mm and lengths to about 12,000–13,000 mm, cut to standard or custom dimensions. Weight per m² = thickness (mm) × 2.71; a 4×8 ft sheet covers 2.972 m².

Tiús	kg/m²	Meáchan in aghaidh an bhileog 4×8
6 mm	16.3	thart. 48.3 kg
8 mm	21.7	thart. 64.4 kg
10 mm	27.1	thart. 80.5 kg
20 mm	54.2	thart. 161 kg
50 mm	135.5	thart. 403 kg
100 mm	271	thart. 805 kg

Feidhmchláir tipiciúla

• Welded storage tanks, boiler and tank lining plates and large anti-corrosion equipment cabinets.
• Chemical process equipment, vessels, pipes and fittings in mild, non-structural service.
• Déantúsaíocht ghinearálta, páirteanna meaisínithe, tooling blanks and spun or stamped components.
• Hot rolled coil as feedstock for cold rolling, fin stock or further finishing.
• Insulation jacketing and cladding where a heavy or wide mill-finish sheet is acceptable.

Because pure 1060 is low strength, do not use H112 plate for high-load or wear parts; roghnaigh 3003 for tougher cladding, 5052 for corrosion with strength, 5083 for marine/structural plate or 6061 for machined structural components.

Wholesale Supply, Rialú Cáilíochta agus Ordú

A wholesale order can specify thickness and tolerance, width and cut length, plate or coil, cineál imeall (scoilt nó sáfa), surface and any protective film, plus cutting, lúbadh, drilling or CNC blanks to drawing.

Mills hold large rolling stocks of common gauges for fast dispatch in full truck or container quantities, with smaller trial lots available.

Quality control covers thickness, leithead/fad agus lamháltas trasnánach, maoile, surface quality and tensile/elongation by thickness on the MTC; ISO 9001 tacaíonn muilte le cigireacht SGS/BV/TUV.

Plate is packed on wooden pallets or in wooden cases with moisture-proof wrapping for export. Leanann an praghas an bonn tinne alúmanaim chomh maith le táille próiseála, so compare per ton and per cut plate on identical gauge, size and Incoterm (FOB/CFR/CIF; coitianta 30% deposit, balance against the bill of lading).

A lua, seol cóimhiotal/temper (1060 H112), tiús, width and length, plate or coil, chainníocht, iarratas agus calafort ceann scríbe.

For wholesale buyers, a direct mill relationship matters more than the lowest single quote: only a mill with hot-rolling capacity can hold thickness and flatness across container lots, supply consistent MTC values and replenish the same gauge month after month.

Confirm genuine capacity with a video of the hot line and the gauges actually rolled, run production-thickness samples through your cutting and welding operations, agus sampla sínithe a úsáid mar an gcaighdeán glactha; is annamh a mheaitseálann trádálaithe atá ag athdhíol spotphlátaí an chomhsheasmhacht seo.

Ceisteanna Coitianta

C: Cad é 1060 H112 alúmanam te-rollta a úsáidtear le haghaidh?

A: Umair táthaithe agus plátaí líneála, trealamh frith-chreimeadh agus ceimiceach, monarú ginearálta, bearnaí meaisínithe, agus corna teorollta mar stoc cothaithe fuarrollta, in medium and heavy gauges.

C: Cad a chiallaíonn H112??

A: Tá sé mar-déanta, meon te-rollta le hairíonna meicniúla íosta ráthaithe ach gan aon obair fhuar rialaithe, a úsáidtear de ghnáth le haghaidh pláta thuas faoi 6 mm.

C: Cén fáth go bhfuil roinnt 1060 pláta liostaithe ag 300-800 MPa?

A: Tá na figiúirí sin mícheart (often copied from steel listings); glan 1060 H112 has tensile minima of roughly 60–75 MPa depending on thickness, and such claims should be rejected.

C: Hot rolled or cold rolled – which do I need?

A: Hot rolled H112 for thick, eacnamaíoch, weldable plate with a mill surface; cold rolled for thin gauges, bright finishes or controlled hardness.

C: Can it be welded and cut to size?

A: Tá. 1060 H112 welds and machines easily and can be sawn, laser or plasma cut, bent and supplied as custom blanks with export packaging.

C: What is the wholesale MOQ and lead time?

A: De ghnáth luaitear mórdhíola in aghaidh an tonna i gcainníochtaí coimeádán/trucail iomlán, le horduithe trialach soshannta; tomhasairí coitianta a choinnítear i long stoc go tapa agus braitheann méideanna saincheaptha ar sceideal an mhuilinn.

Conclúid

Mórdhíola 1060 Is é H112 alúmanam te-rollta an eacnamaíoch, insínte, pláta íon-alúmanam weldable le haghaidh umair, líneálacha, anti-corrosion equipment, déantúsaíocht agus stoc cothaithe fuarrollta i dtomhasairí troma.

Sonraigh tiús, width and length, cheannach ar an GB/T ráthaithe 3880 maoine agus deimhnithe muilne seachas éilimh neartaithe ar líne, agus cosúlachtaí in aghaidh an tonna a chur i gcomparáid faoin Incoterm céanna.