Slàn-reic 1060 H112 Hot Rolled Aluminium: Meudan, Feartan agus Solarachadh

Ro-ràdh

Buyers looking for wholesale 1060 H112 hot rolled aluminum are usually sourcing thick, mill-finish plate or hot rolled coil in volume—as welded tank and lining plate, anti-corrosion equipment, general fabrication stock or feedstock for cold rolling.

1060 is a commercially pure aluminum (as lugha 99.60% Al), and the H112 temper identifies plate produced by hot rolling with guaranteed minimum mechanical properties.

Hot rolled H112 plate is the most economical way to buy 1060 in medium and heavy gauges: it is soft and ductile, resistant corrach, easy to weld and machine, and available in large widths and lengths.

This guide explains the H112 temper, how hot rolled differs from cold rolled, the composition and properties, standard sizes and weights, iarrtasan, and how to order wholesale factory-direct.

What Does the H112 Temper Mean?

H112 is an “as-fabricated” temper for products shaped by hot working. Its key points are:

• The plate obtains its strength from the hot rolling process rather than controlled cold work.
• The exact degree of strain hardening is not controlled, but the standard sets guaranteed minimum mechanical properties.
• It is typically used for thicker plate (from about 6 mm upward) supplied straight from hot rolling with only leveling.
• Because it is not deliberately cold-hardened, H112 stays ductile and weldable and is well suited to later forming, machining or further processing.

For comparison, F is the fully free as-fabricated state with no property guarantees, H111 is annealed with only light hardening from leveling, and the H1x/H2x tempers are cold-rolled conditions.

H112 sits between them: hot worked, yet certified to minimum strength and elongation.

Hot rolling is especially well matched to pure aluminum: worked above its recrystallization temperature, the metal flows without the large residual stresses and edge cracking that hard cold work can cause in thick sections,

and the continuously recrystallized grain keeps the plate isotropic and easy to weld or machine.

After leveling it leaves the mill essentially stress-relieved and flat, which is why fabricators prefer H112 for large welded structures that must stay dimensionally stable rather than distort after cutting.

Hot Rolled vs Cold Rolled Aluminum

	Teth air a roiligeadh (H112)	Rolladh fuar
Pròiseas	rolled above the recrystallization temperature	rolled at room temperature
Tigheadas	medium and heavy plate, typically about 6–300 mm+	thin sheet and foil, below about 6 mm
Uachdar	dark/bright mill finish, slightly less smooth	rèidh, geal, tight-tolerance surface
Feartan	bog, dà-fhillte, low residual stress; cold-rolling feedstock	harder or precision tempers (O/H14/H18)
Cosgais	lower per kg in heavy gauges	higher processing cost for thin/bright product

 

Choose hot rolled H112 when thickness, price, weldability or later processing dominates and a polished surface is not required; choose cold rolled for thin gauges, bright finishes or precise hardness.

Co-dhèanamh ceimigeach agus feartan meacanaigeach

Eileamaid	Al	Agus	Fe	Cu	Mn	Tha mg	Zn
1060	≥99.60	≤0.25	≤0.35	≤0.05	≤0.03	≤0.03	≤0.05

 

Minimum H112 properties fall slightly with very heavy section (airson GB/T 3880); note that some online listings wrongly quote steel-like 300–800 MPa values for 1060, which are impossible for pure aluminum and should be ignored:

Tigheadas (mm)	Neart teasile (min)	Leudachadh (min)
>4.5–6	75 MPa	10%
>6–12.5	75 MPa	10%
>12.5—40	70 MPa	18%
>40–80	60 MPa	22%

 

Density is about 2.71 g/cm³; thermal conductivity is high and weldability is excellent. Confirm the guaranteed values for your thickness on the mill test certificate.

Standard Sizes and Plate Weight

1060 H112 hot rolled plate is supplied from about 6 mm to 200–300 mm (heavier on request), in widths up to roughly 2600–5000 mm and lengths to about 12,000–13,000 mm, cut to standard or custom dimensions. Weight per m² = thickness (mm) × 2.71; a 4×8 ft sheet covers 2.972 m².

Tigheadas	kg/m²	Weight per 4×8 sheet
6 mm	16.3	Mu thuairmse. 48.3 kg
8 mm	21.7	Mu thuairmse. 64.4 kg
10 mm	27.1	Mu thuairmse. 80.5 kg
20 mm	54.2	Mu thuairmse. 161 kg
50 mm	135.5	Mu thuairmse. 403 kg
100 mm	271	Mu thuairmse. 805 kg

Cleachdaidhean àbhaisteach

• Welded storage tanks, boiler and tank lining plates and large anti-corrosion equipment cabinets.
• Chemical process equipment, vessels, pipes and fittings in mild, non-structural service.
• Saothrachadh coitcheann, pàirtean innealta, tooling blanks and spun or stamped components.
• Hot rolled coil as feedstock for cold rolling, fin stock or further finishing.
• Insulation jacketing and cladding where a heavy or wide mill-finish sheet is acceptable.

Because pure 1060 is low strength, do not use H112 plate for high-load or wear parts; tagh 3003 for tougher cladding, 5052 for corrosion with strength, 5083 for marine/structural plate or 6061 for machined structural components.

Wholesale Supply, Quality Control and Ordering

A wholesale order can specify thickness and tolerance, width and cut length, plate or coil, edge type (slit or sawn), surface and any protective film, a bharrachd air gearradh, A 'lùbadh, drileadh no beàrnan CNC gu tarraing.

Bidh muilnean a’ cumail stoc mòr de shlatan-tomhais cumanta airson an cur gu sgiobalta ann an làn làraidh no soithichean, le lotaichean deuchainn nas lugha rim faighinn.

Tha smachd càileachd a 'còmhdach tiugh, leud / fad agus fulangas trastain, rèidh, càileachd uachdar agus tensile / leudachadh a rèir tiugh air an MTC; ISO 9001 muilnean a’ toirt taic do sgrùdadh SGS/BV/TUV.

Tha plàta air a phacadh air màileidean fiodha no ann an cèisean fiodha le còmhdach dìon-taise airson às-mhalairt. Tha prìs a’ leantainn bunait ingot alùmanum a bharrachd air cìs giollachd, mar sin dèan coimeas eadar gach tunna agus gach truinnsear gearraidh air an aon thomhas, meud agus Incoterm (FOB/CFR/CIF; cumanta 30% tasgadh, cothromachadh an aghaidh a’ bhile lading).

Gus luaidh, cuir alloy / temper (1060 H112), tiughad, leud agus fad, plate or coil, meud, tagradh agus port ceann-uidhe.

Airson luchd-ceannach mòr-reic, tha dàimh muilne dìreach nas cudromaiche na an cuòt singilte as ìsle: chan urrainn ach muileann le comas ruith teth tiugh agus rèidh a chumail thairis air lotaichean soithichean, thoir seachad luachan cunbhalach MTC agus ath-lìonadh an aon shlat-tomhais mìos às deidh mìos.

Confirm genuine capacity with a video of the hot line and the gauges actually rolled, run production-thickness samples through your cutting and welding operations, and use a signed sample as the receiving standard; traders reselling spot plate rarely match this consistency.

Ceistean Cumanta

C: Na th’ann 1060 H112 hot rolled aluminum used for?

A: Welded tanks and lining plates, anti-corrosion and chemical equipment, general fabrication, machined blanks, and hot rolled coil as cold-rolling feedstock, in medium and heavy gauges.

C: What does H112 mean?

A: It is an as-fabricated, hot-rolled temper with guaranteed minimum mechanical properties but no controlled cold work, typically used for plate above about 6 mm.

C: Why is some 1060 plate listed at 300-800 MPa?

A: Those figures are erroneous (often copied from steel listings); fìor-ghlan 1060 H112 has tensile minima of roughly 60–75 MPa depending on thickness, and such claims should be rejected.

C: Hot rolled or cold rolled – which do I need?

A: Hot rolled H112 for thick, eaconamach, weldable plate with a mill surface; cold rolled for thin gauges, bright finishes or controlled hardness.

C: Can it be welded and cut to size?

A: Tha. 1060 H112 welds and machines easily and can be sawn, laser or plasma cut, bent and supplied as custom blanks with export packaging.

C: What is the wholesale MOQ and lead time?

A: Wholesale is usually quoted per ton in full container/truck quantities, le òrdughan deuchainn air an rèiteachadh; common gauges held in stock ship quickly and custom sizes depend on the mill schedule.

Co-dhùnadh

Slàn-reic 1060 H112 hot rolled aluminum is the economical, dà-fhillte, weldable pure-aluminum plate for tanks, linings, anti-corrosion equipment, fabrication and cold-rolling feedstock in heavy gauges.

Specify thickness, leud agus fad, buy on the guaranteed GB/T 3880 properties and mill certificates rather than inflated online strength claims, and compare like-for-like per ton under the same Incoterm.