1100 Fèy aliminyòm pou vann: Klas, Gwosè ak gid pou achtè a

Prezantasyon

1100 aluminum sheet is one of the most practical commercially pure aluminum plates you can buy: with a minimum 99.0% aluminum content and a small copper addition, it is slightly stronger than 1050/1060 while keeping excellent formability, rezistans korozyon, weldability and thermal conductivity.

It is the default sheet for chemical equipment, cookware and deep-drawn parts, koule chalè, signs and general fabrication that do not need high strength.

Offered factory-direct, 1100 sheet can be supplied in standard 4×8 ft and metric sizes or cut to your dimensions, with the temper and surface finish the product needs.

This guide covers the composition, pwopriyete yo, sizes and weights, aplikasyon yo, fabwikasyon, ki jan li konpare ak 1050, 1060 epi 3003, ak kijan pou bay lòd.

Ki sa ki 1100 Fèy aliminyòm?

1100 is a non-heat-treatable 1xxx-series alloy strengthened only by cold work and softened by annealing. Sheet generally runs about 0.2–6 mm thick (thicker material is plate), supplied flat or cut to length. Avantaj karakteristik li yo se:

• Ekselan duktilite pou koube, Stamping, k ap vire ak desen gwo twou san fon, espesyalman nan O tanperaman an.
• Very good atmospheric and chemical corrosion resistance from the self-healing oxide film.
• Yon ti kras pi wo fòs pase 1050/1060 thanks to a controlled 0.05–0.20% copper addition.
• High thermal and electrical conductivity, plus excellent weldability and easy machining.
• Limyè (sou 2.71 g/cm³), rust-free and lower cost than alloyed grades; anodizes to a good film.
• The trade-off is modest strength; load-bearing or wear parts should use 3003, 5052 oswa 6061.

Konpozisyon chimik ak pwopriyete mekanik

Chimi kontwole (per ASTM B209 / GB/T 3190) keeps silicon plus iron and copper within tight limits so forming, welding and corrosion performance stay high:

Eleman	Al	Epi + Fe	Cu	Mn	Zn
1100	≥99.0	≤0.95	0.05–0.20	≤0.05	≤0.10

 

Mechanical properties change with temper, konsa menm bagay la tou 1100 ka fèy dwe apwovizyone mou ak gwo twou san fon-drawable oswa difisil ak rijid (typical Rm values):

Tanperaman	Tensile (MPa)	Karaktè
O (rkant)	apeprè. 75–110	Pi mou; Desen gwo twou san fon, k ap vire, fòmabilite maksimòm
H12 / H22	apeprè. 95–125	Trimès-difisil; limyè fòme
H14 / H24	apeprè. 110–150	Mwatye-difisil; common general-purpose temper
H16 / H26	apeprè. 135–170	Twa-ka-difisil; panno pi rèd
H18	apeprè. 150–200	Full-difisil; rijid, fòm limite

 

Valè yo varye yon ti kras ak epesè ak estanda; confirm tensile and yield on the mill certificate for your gauge.

The small copper addition is what distinguishes 1100 in service.

It gives a modest but useful gain in strength without sacrificing the pure-aluminum forming that lets the sheet be drawn into deep pots and liners, and the metal still anodizes into a uniform, protective film used on trim and nameplates.

1100 thus occupies a deliberate middle ground—not as soft and conductive as 1060, but not as alloyed as 3003, which is why it appears so often in cookware, chemical and general-purpose stock.

Gwosè estanda, Sifas ak pwa

1100 fèy se pwodwi soti nan apeprè 0.2 pou 6 mm (plak pou 200 mm + sou demann), nan lajè jiska apeprè 2600 mm ak longè a 12,000 mm. Common sizes include 4×8 ft (1219×2438), 1000×2000, 1220×2440, 1250×2500 and 1500×3000, plus custom blanks to drawing.

Sifas / kaba	Itilizasyon tipik
Mill fini (optional PVC/PVDF protective film)	Fèy jeneral, stock fabwikasyon, CLADDING
Bwose / glas	Panno dekoratif, nameplates, ekleraj
Anodize / koulè-kouvwi	Chemical and outdoor panels, durable signage, taye
Relief / circles	Izolasyon, anti-slip, cookware discs and deep-drawn parts

 

Weight is easy at 2.71 g/cm³: kg pa m² = epesè (mm) × 2.71; a 4×8 ft sheet covers about 2.972 m².

Epesè	kg/m²	Pwa pou chak fèy 4 × 8
0.5 mm	1.36	apeprè. 4.0 kg
1.0 mm	2.71	apeprè. 8.1 kg
1.5 mm	4.07	apeprè. 12.1 kg
2.0 mm	5.42	apeprè. 16.1 kg
3.0 mm	8.13	apeprè. 24.2 kg

Aplikasyon tipik

• Ekipman pwosesis chimik, tank depo, veso, pipes and fittings that need corrosion resistance and weldability.
• Isto, cooking utensils and deep-drawn or spun parts, plus aluminum circles for pots and pans.
• Lavabo chalè, reflektè lanp, boutèy bouchon stock, printing plates and food packaging components.
• Siy, nameplates and decorative or anodized architectural trim, and general stamped or bent parts.

Fabrication and Surface Treatment

1100 cuts, shears, bends and forms readily and can be laser, plasma or water-jet cut, estoke, spun and drilled; it welds cleanly by common processes and takes anodizing, bwose, polishing and coating well.

Use O temper for the deepest draws and harder tempers where the finished part must hold shape; generous bend radii and clean, oil-free surfaces help on high-speed lines.

1100 vs 1050, 1060 epi 3003

Egalize	Min. Al / alyaj	Fòs	Pi bon anfòm
1050	99.50% Al	Ba	Most economical general sheet and cladding
1060	99.60% Al	Ba	Best conductivity/reflectivity; signs and electrical parts
1100	99.00% Al, yon ti Cu	Ba-mwayen	Yon ti kras pi fò; fòme, soude, chimik, isto
3003	Al + Mn (sou 1.2%)	Mwayen	Konsènan 20% fò; planche yo, tread, tougher cladding

 

Chwazi 1100 when you need a little more strength and weldability than 1050/1060 with the same pure-aluminum forming and corrosion; monte jiska 3003 for real added strength.

Kontwòl Kalite, Pricing and How to Order

QC covers thickness and flatness, lajè / longè ak tolerans dyagonal, surface quality and tensile/yield by temper and chemistry on the MTC; ISO 9001 mills support SGS/BV inspection.

Sheet is interleaved with protective film and packed on pallets or in cases with moisture-proof wrapping for export. Pricing swiv baz ingot aliminyòm plis yon frè pwosesis, with thinner/wider gauge, koutim koupe, tretman sifas ak ti kantite ajoute pri;

compare per ton and per finished blank on identical specs under FOB/CFR/CIF (souvan 30% depo, balans kont bòdwo chaj la). Pou site, voye alyaj/tanperaman (1100), epesè, fèy oswa dimansyon vid, sifas, kantite, aplikasyon ak pò destinasyon.

Verify new material on production-gauge samples rather than photos: run the sheet through your forming, welding or cutting line at normal speed, mezire epesè atravè lajè a, inspect the surface and, for food or chemical use, confirm the compliance paperwork matches the lot.

A signed pre-production sample then becomes the receiving standard, and an integrated mill that rolls and finishes in-house will hold that standard more reliably across repeat orders than spot resellers.

Kesyon yo poze souvan

K: Ki sa ki 1100 fèy aliminyòm itilize pou?

A: Chemical tanks, vessels and piping, cookware and deep-drawn parts, koule chalè, siy, bottle cap and printing stock, and general fabrication needing formability and corrosion rather than high strength.

K: Ki jan fò 1100 konpare ak 1060 epi 3003?

A: It is slightly stronger than 1050/1060 due to a small copper addition, mè 3003 (manganèz) is about 20% fò; H18 1100 reaches roughly 150–200 MPa tensile.

K: Ki tanperaman mwen ta dwe chwazi?

A: O for deep drawing and spinning, H14/H24 for general sheet, H16/H26 for stiffer panels and H18 for the most rigid plate with little forming.

K: What sizes and thicknesses are available?

A: About 0.2–6 mm sheet in widths to roughly 2600 mm, ki gen ladan 4 × 8 pye ak estanda metrik, with plate and cut-to-size blanks on request.

K: Can it be welded, anodized and cut to size?

A: Yes—1100 welds cleanly, anodizes and finishes well, and can be laser or sawn cut, bent and supplied as custom blanks with protective film.

K: Konbyen yon fèy 4 × 8 peze?

A: Apeprè 8.1 kg nan 1 mm, 12.1 kg nan 1.5 mm, 16.1 kg nan 2 mm ak 24.2 kg nan 3 mm, lè l sèvi avèk kg/m² = epesè (mm) × 2.71 sou 2.972 m².

Konklizyon

1100 aluminum sheet is the slightly stronger, easy-to-fabricate pure-aluminum plate for chemical equipment, isto, heat transfer and signs.

Espesifye tanperaman an nan fason yo trete panèl la, ranje epesè ak koupe gwosè, choose the surface, epi achte sou sètifika moulen, tolerans ak echantiyon apwouve olye ke pri pou kont li.