1100 Aluminium Sheet for Sale: biji, Ukuran lan Pandhuan Pembeli
1100 Aluminium Sheet for Sale: biji, Ukuran lan Pandhuan Pembeli
Pambuka
1100 aluminum sheet is one of the most practical commercially pure aluminum plates you can buy: with a minimum 99.0% aluminum content and a small copper addition, it is slightly stronger than 1050/1060 while keeping excellent formability, resistance karat, weldability and thermal conductivity.
It is the default sheet for chemical equipment, cookware and deep-drawn parts, panas sinks, signs and general fabrication that do not need high strength.
Offered factory-direct, 1100 sheet can be supplied in standard 4×8 ft and metric sizes or cut to your dimensions, with the temper and surface finish the product needs.
This guide covers the composition, Properties, sizes and weights, aplikasi, Pabrikan, carane mbandhingaké karo 1050, 1060 lan 3003, lan carane supaya.
Apa Apa 1100 Lembaran Aluminium?
1100 is a non-heat-treatable 1xxx-series alloy strengthened only by cold work and softened by annealing. Sheet generally runs about 0.2–6 mm thick (thicker material is plate), supplied flat or cut to length. Kaluwihan karakteristike yaiku:
- ductility banget kanggo mlengkung, stamping, Spinning lan drawing jero, utamané ing watek O.
- Very good atmospheric and chemical corrosion resistance from the self-healing oxide film.
- Kekuwatan rada luwih dhuwur tinimbang 1050/1060 thanks to a controlled 0.05–0.20% copper addition.
- High thermal and electrical conductivity, plus excellent weldability and easy machining.
- cahya (Babagan 2.71 g/cm³), rust-free and lower cost than alloyed grades; anodizes to a good film.
- The trade-off is modest strength; load-bearing or wear parts should use 3003, 5052 utawa 6061.
Komposisi Kimia lan Sifat Mekanik
Kimia sing dikontrol (per ASTM B209 / GB / t 3190) keeps silicon plus iron and copper within tight limits so forming, welding and corrosion performance stay high:
| unsur | Al | lan + Fe | Cu | Mn | Zn |
| 1100 | ≥990 | ≤0,95 | 0.05–0.20 | ≤0.05 | ≤0.10 |
Mechanical properties change with temper, dadi padha 1100 sheet bisa diwenehake alus lan jero-drawable utawa hard lan kaku (typical Rm values):
| Temper | Tensile (MPa) | Watak |
| O (Anneeled) | kira-kira. 75-110 | Paling empuk; gambar jero, Spinning, formability maksimum |
| H12 / H22 | kira-kira. 95–125 | Kuat seprapat; cahya mbentuk |
| H14 / H24 | kira-kira. 110-150 | Setengah hard; common general-purpose temper |
| H16 / H26 | kira-kira. 135-170 | Telung seprapat-hard; panel kaku |
| H18 | kira-kira. 150-200 | Full-hard; kaku, mbentuk winates |
Nilai beda-beda rada karo kekandelan lan standar; confirm tensile and yield on the mill certificate for your gauge.
The small copper addition is what distinguishes 1100 in service.
It gives a modest but useful gain in strength without sacrificing the pure-aluminum forming that lets the sheet be drawn into deep pots and liners, and the metal still anodizes into a uniform, protective film used on trim and nameplates.
1100 thus occupies a deliberate middle ground—not as soft and conductive as 1060, but not as alloyed as 3003, which is why it appears so often in cookware, chemical and general-purpose stock.
Ukuran Standar, Lumahing lan Bobot
1100 sheet diprodhuksi saka babagan 0.2 kanggo 6 mm (piring kanggo 200 mm + ing panyuwunan), ing jembaré nganti kira-kira 2600 mm lan dawa kanggo 12,000 mm. Common sizes include 4×8 ft (1219×2438), 1000×2000, 1220×2440, 1250×2500 and 1500×3000, plus custom blanks to drawing.
| lumahing / Rampung | Panggunaan khas |
| Mill rampung (optional PVC/PVDF protective film) | Lembar umum, saham pabrikan, cladding |
| Disikat / Pangilon | Panel hiasan, Nameplates, lampu |
| Anodisasi / dilapisi warna | Chemical and outdoor panels, durable signage, Trim |
| Emboss / circles | Isolasi, anti-slip, cookware discs and deep-drawn parts |
Weight is easy at 2.71 g/cm³: kg per m² = ketebalan (mm) × 2.71; a 4×8 ft sheet covers about 2.972 m².
| kekandelan | kg/m² | Bobot saben 4 × 8 lembar |
| 0.5 mm | 1.36 | kira-kira. 4.0 kg |
| 1.0 mm | 2.71 | kira-kira. 8.1 kg |
| 1.5 mm | 4.07 | kira-kira. 12.1 kg |
| 2.0 mm | 5.42 | kira-kira. 16.1 kg |
| 3.0 mm | 8.13 | kira-kira. 24.2 kg |
Aplikasi Khas
- Peralatan pangolahan kimia, tank panyimpenan, prau, pipes and fittings that need corrosion resistance and weldability.
- Cookware, cooking utensils and deep-drawn or spun parts, plus aluminum circles for pots and pans.
- Panas klelep, reflektor lampu, stok tutup botol, printing plates and food packaging components.
- Signs, nameplates and decorative or anodized architectural trim, and general stamped or bent parts.
Fabrication and Surface Treatment
1100 cuts, shears, bends and forms readily and can be laser, plasma or water-jet cut, dicap, spun and drilled; it welds cleanly by common processes and takes anodizing, sikat, polishing and coating well.
Use O temper for the deepest draws and harder tempers where the finished part must hold shape; generous bend radii and clean, oil-free surfaces help on high-speed lines.
1100 vs 1050, 1060 lan 3003
| Kelas | Min. Al / paduan | kekuwatan | Paling pas |
| 1050 | 99.50% Al | Kurang | Most economical general sheet and cladding |
| 1060 | 99.60% Al | Kurang | Best conductivity/reflectivity; signs and electrical parts |
| 1100 | 99.00% Al, a little Cu | Sedheng-sedheng | Rada kuwat; mbentuk, welding, kimia, Cookware |
| 3003 | Al + Mn (Babagan 1.2%) | Medium | Babagan 20% Kuat; jubin, tread, tougher cladding |
Pilih 1100 when you need a little more strength and weldability than 1050/1060 with the same pure-aluminum forming and corrosion; step up to 3003 for real added strength.
Kontrol Kualitas, Pricing and How to Order
QC covers thickness and flatness, jembaré / dawa lan toleransi diagonal, surface quality and tensile/yield by temper and chemistry on the MTC; ISO 9001 mills support SGS/BV inspection.
Sheet is interleaved with protective film and packed on pallets or in cases with moisture-proof wrapping for export. Rega nderek basis ingot aluminium plus ragad Processing, with thinner/wider gauge, nglereni adat, perawatan lumahing lan jumlah cilik nambah biaya;
compare per ton and per finished blank on identical specs under FOB/CFR/CIF (umume 30% simpenan, imbangan marang bill of lading). Kanggo ngutip, ngirim alloy / watek (1100), ketebalan, sheet or blank dimensions, lumahing, jumlahe, aplikasi lan port tujuan.
Verify new material on production-gauge samples rather than photos: run the sheet through your forming, welding or cutting line at normal speed, ngukur kekandelan liwat jembaré, inspect the surface and, for food or chemical use, confirm the compliance paperwork matches the lot.
A signed pre-production sample then becomes the receiving standard, and an integrated mill that rolls and finishes in-house will hold that standard more reliably across repeat orders than spot resellers.
Pitakonan sing Sering Ditakoni
Q: Apa iku 1100 sheet aluminium digunakake kanggo?
A: Chemical tanks, vessels and piping, cookware and deep-drawn parts, panas sinks, Tandha, bottle cap and printing stock, and general fabrication needing formability and corrosion rather than high strength.
Q: Sepira kuat 1100 dibandhingake 1060 lan 3003?
A: It is slightly stronger than 1050/1060 due to a small copper addition, Nanging 3003 (mangan) is about 20% Kuat; H18 1100 reaches roughly 150–200 MPa tensile.
Q: Temperamen apa sing kudu dak pilih?
A: O for deep drawing and spinning, H14/H24 for general sheet, H16/H26 for stiffer panels and H18 for the most rigid plate with little forming.
Q: What sizes and thicknesses are available?
A: About 0.2–6 mm sheet in widths to roughly 2600 mm, kalebu 4 × 8 ft lan standar metrik, with plate and cut-to-size blanks on request.
Q: Can it be welded, anodized and cut to size?
A: Yes—1100 welds cleanly, anodizes and finishes well, and can be laser or sawn cut, bent and supplied as custom blanks with protective film.
Q: Pira lembar 4 × 8 bobote?
A: Kira-kira 8.1 kg ing 1 mm, 12.1 kg ing 1.5 mm, 16.1 kg ing 2 mm lan 24.2 kg ing 3 mm, nggunakake kg / m² = kekandelan (mm) × 2.71 liwat 2.972 m².
Kesimpulan
1100 aluminum sheet is the slightly stronger, easy-to-fabricate pure-aluminum plate for chemical equipment, Cookware, heat transfer and signs.
Nemtokake temperamen saka carane panel diproses, ndandani kekandelan lan ukuran potong, choose the surface, lan tuku ing sertifikat pabrik, toleransi lan sampel disetujoni tinimbang rega piyambak.
