1100 판매용 알루미늄 시트: 등급, 크기 및 구매자 가이드

소개

1100 aluminum sheet is one of the most practical commercially pure aluminum plates you can buy: with a minimum 99.0% aluminum content and a small copper addition, it is slightly stronger than 1050/1060 while keeping excellent formability, 내식성, weldability and thermal conductivity.

It is the default sheet for chemical equipment, cookware and deep-drawn parts, 방열판, signs and general fabrication that do not need high strength.

Offered factory-direct, 1100 sheet can be supplied in standard 4×8 ft and metric sizes or cut to your dimensions, with the temper and surface finish the product needs.

This guide covers the composition, 속성, sizes and weights, 애플리케이션, 제작, 와 어떻게 비교되는가 1050, 1060 그리고 3003, and how to order.

무엇인가요 1100 알루미늄 시트?

1100 is a non-heat-treatable 1xxx-series alloy strengthened only by cold work and softened by annealing. Sheet generally runs about 0.2–6 mm thick (thicker material is plate), supplied flat or cut to length. 그 특징적인 장점은:

• 굽힘에 대한 연성이 우수함, 스탬핑, 회전 및 딥 드로잉, 특히 O 성격에.
• Very good atmospheric and chemical corrosion resistance from the self-healing oxide film.
• 보다 약간 더 높은 강도 1050/1060 thanks to a controlled 0.05–0.20% copper addition.
• High thermal and electrical conductivity, plus excellent weldability and easy machining.
• 빛 (~에 대한 2.71 g/cm³), rust-free and lower cost than alloyed grades; anodizes to a good film.
• The trade-off is modest strength; load-bearing or wear parts should use 3003, 5052 또는 6061.

화학적 조성 및 기계적 성질

통제된 화학 (per ASTM B209 / GB/T 3190) keeps silicon plus iron and copper within tight limits so forming, welding and corrosion performance stay high:

요소	알	그리고 + 철	Cu	망간	아연
1100	≥99.0	≤0.95	0.05-0.20	≤0.05	≤0.10

 

Mechanical properties change with temper, 그래서 똑같다 1100 시트는 부드럽고 깊게 그리기 가능하거나 단단하고 단단하게 공급될 수 있습니다. (typical Rm values):

성질	인장 (MPa)	성격
영형 (어닐링)	대략. 75-110	가장 부드러운; 딥 드로잉, 제사, 최대 성형성
H12 / H22	대략. 95–125	쿼터 하드; 가벼운 형성
H14 / H24	대략. 110-150	반하드; common general-purpose temper
H16 / H26	대략. 135-170	3/4 하드; 더 단단한 패널
H18	대략. 150-200	풀하드; 엄격한, 제한된 형성

 

두께와 규격에 따라 값이 조금씩 다름; confirm tensile and yield on the mill certificate for your gauge.

The small copper addition is what distinguishes 1100 in service.

It gives a modest but useful gain in strength without sacrificing the pure-aluminum forming that lets the sheet be drawn into deep pots and liners, and the metal still anodizes into a uniform, protective film used on trim and nameplates.

1100 thus occupies a deliberate middle ground—not as soft and conductive as 1060, but not as alloyed as 3003, which is why it appears so often in cookware, chemical and general-purpose stock.

표준 크기, 표면과 무게

1100 시트는 약 0.2 에게 6 mm (접시에 200 요청 시 mm+), 너비는 대략적으로 2600 mm 및 길이 12,000 mm. Common sizes include 4×8 ft (1219×2438), 1000×2000, 1220×2440, 1250×2500 and 1500×3000, plus custom blanks to drawing.

표면 / 마치다	일반적인 사용
밀 마무리 (optional PVC/PVDF protective film)	일반 시트, 제조 재고, 클 래 딩
브러시드 / 거울	장식 패널, 명판, 조명
양극 처리 / 컬러 코팅	Chemical and outdoor panels, durable signage, 손질
양각 / circles	단열재, anti-slip, cookware discs and deep-drawn parts

 

Weight is easy at 2.71 g/cm³: kg/m² = 두께 (mm) × 2.71; a 4×8 ft sheet covers about 2.972 m².

두께	kg/m²	4×8장당 무게
0.5 mm	1.36	대략. 4.0 킬로그램
1.0 mm	2.71	대략. 8.1 킬로그램
1.5 mm	4.07	대략. 12.1 킬로그램
2.0 mm	5.42	대략. 16.1 킬로그램
3.0 mm	8.13	대략. 24.2 킬로그램

일반적인 응용 분야

• 화학 공정 장비, 저장 탱크, 선박, pipes and fittings that need corrosion resistance and weldability.
• 조리기구, cooking utensils and deep-drawn or spun parts, plus aluminum circles for pots and pans.
• 방열판, 램프 반사경, 병뚜껑 있음, printing plates and food packaging components.
• 손짓, nameplates and decorative or anodized architectural trim, and general stamped or bent parts.

Fabrication and Surface Treatment

1100 cuts, shears, bends and forms readily and can be laser, plasma or water-jet cut, 스탬프가 찍힌, spun and drilled; it welds cleanly by common processes and takes anodizing, 브러싱, polishing and coating well.

Use O temper for the deepest draws and harder tempers where the finished part must hold shape; generous bend radii and clean, oil-free surfaces help on high-speed lines.

1100 대 1050, 1060 그리고 3003

등급	최소. 알 / 합금화	힘	최적의 핏
1050	99.50% 알	낮은	Most economical general sheet and cladding
1060	99.60% 알	낮은	Best conductivity/reflectivity; signs and electrical parts
1100	99.00% 알, 약간의 구리	낮음-중간	약간 더 강함; 형성, 용접, 화학적인, 조리기구
3003	알 + 망간 (~에 대한 1.2%)	중간	에 대한 20% 더 강력합니다; 바닥, tread, tougher cladding

 

선택하다 1100 when you need a little more strength and weldability than 1050/1060 with the same pure-aluminum forming and corrosion; 한 단계 더 나아가다 3003 for real added strength.

품질 관리, Pricing and How to Order

QC covers thickness and flatness, 폭/길이 및 대각선 공차, surface quality and tensile/yield by temper and chemistry on the MTC; ISO 9001 mills support SGS/BV inspection.

Sheet is interleaved with protective film and packed on pallets or in cases with moisture-proof wrapping for export. 가격은 알루미늄 주괴 베이스와 가공 수수료를 따릅니다., with thinner/wider gauge, 맞춤 절단, 표면 처리 및 소량으로 비용 추가;

compare per ton and per finished blank on identical specs under FOB/CFR/CIF (천하게 30% 보증금, 선하증권과의 잔액). 인용하려면, 합금/성미 보내기 (1100), 두께, 시트 또는 빈 치수, 표면, 수량, 애플리케이션 및 대상 포트.

Verify new material on production-gauge samples rather than photos: run the sheet through your forming, welding or cutting line at normal speed, measure thickness across the width, inspect the surface and, for food or chemical use, confirm the compliance paperwork matches the lot.

A signed pre-production sample then becomes the receiving standard, and an integrated mill that rolls and finishes in-house will hold that standard more reliably across repeat orders than spot resellers.

자주 묻는 질문

큐: 무엇인가요 1100 에 사용되는 알루미늄 시트?

ㅏ: Chemical tanks, vessels and piping, cookware and deep-drawn parts, 방열판, 표지판, bottle cap and printing stock, and general fabrication needing formability and corrosion rather than high strength.

큐: 얼마나 강한 1100 와 비교하다 1060 그리고 3003?

ㅏ: It is slightly stronger than 1050/1060 due to a small copper addition, 하지만 3003 (망간) is about 20% 더 강력합니다; H18 1100 reaches roughly 150–200 MPa tensile.

큐: 어떤 성격을 선택해야 할까요??

ㅏ: O for deep drawing and spinning, H14/H24 for general sheet, H16/H26 for stiffer panels and H18 for the most rigid plate with little forming.

큐: What sizes and thicknesses are available?

ㅏ: About 0.2–6 mm sheet in widths to roughly 2600 mm, 4×8피트 및 미터법 표준 포함, with plate and cut-to-size blanks on request.

큐: Can it be welded, anodized and cut to size?

ㅏ: Yes—1100 welds cleanly, anodizes and finishes well, and can be laser or sawn cut, bent and supplied as custom blanks with protective film.

큐: 4×8 시트의 무게는 얼마입니까??

ㅏ: 대충 8.1 kg ~에 1 mm, 12.1 kg ~에 1.5 mm, 16.1 kg ~에 2 MM과 24.2 kg ~에 3 mm, kg/m² = 두께 사용 (mm) × 2.71 ~ 위에 2.972 m².

결론

1100 aluminum sheet is the slightly stronger, easy-to-fabricate pure-aluminum plate for chemical equipment, 조리기구, heat transfer and signs.

패널 처리 방법에 따라 성질을 지정하십시오., 두께 및 절단 크기 고정, choose the surface, 공장 인증서로 구매, tolerances and approved samples rather than price alone.