1100 Лавҳаи алюминий барои фурӯш: Баҳоҳо, Андозаҳо ва дастури харидор

Шиноскунӣ

1100 aluminum sheet is one of the most practical commercially pure aluminum plates you can buy: with a minimum 99.0% aluminum content and a small copper addition, it is slightly stronger than 1050/1060 while keeping excellent formability, муқовимат ба зангзании, weldability and thermal conductivity.

It is the default sheet for chemical equipment, cookware and deep-drawn parts, гармӣ, signs and general fabrication that do not need high strength.

Offered factory-direct, 1100 sheet can be supplied in standard 4×8 ft and metric sizes or cut to your dimensions, with the temper and surface finish the product needs.

This guide covers the composition, Хусусиятҳо, sizes and weights, барномаҳо, фиреб, бо чй гуна мукоиса мекунад 1050, 1060 ва 3003, and how to order.

Чӣ аст 1100 Лавҳаи алюминий?

1100 is a non-heat-treatable 1xxx-series alloy strengthened only by cold work and softened by annealing. Sheet generally runs about 0.2–6 mm thick (thicker material is plate), supplied flat or cut to length. Афзалиятҳои хоси он мебошанд:

• Кобилияти аъло барои хам кардан, мӯҳр мондан, ресандагӣ ва кашидани чуқур, махсусан дар О.
• Very good atmospheric and chemical corrosion resistance from the self-healing oxide film.
• Қуввати каме баландтар аз 1050/1060 thanks to a controlled 0.05–0.20% copper addition.
• High thermal and electrical conductivity, plus excellent weldability and easy machining.
• Сабук (дар бораи 2.71 г/см³), rust-free and lower cost than alloyed grades; anodizes to a good film.
• The trade-off is modest strength; load-bearing or wear parts should use 3003, 5052 ё 6061.

Таркиби химиявӣ ва хосиятҳои механикӣ

Химияи назоратшаванда (per ASTM B209 / GB / T 3190) keeps silicon plus iron and copper within tight limits so forming, welding and corrosion performance stay high:

Элемент	Ал	Ва + Фе	Cu	Мн	Зн
1100	≥99.0	≤0,95	0.05– 0,20	≤0.05	≤0.10

 

Mechanical properties change with temper, so the same 1100 sheet can be supplied soft and deep-drawable or hard and rigid (typical Rm values):

Табиат	кашиш (МПа)	Характер
О (солагӣ)	террас. 75– 110	Нармтарин; кашидани чуқур, ресандагӣ, максималии шаклгиранда
H12 / H22	террас. 95–125	Quarter-hard; light forming
H14 / H24	террас. 110-150	Ним сахт; common general-purpose temper
H16 / H26	террас. 135-170	Three-quarter-hard; stiffer panels
H18	террас. 150– 200	Пур-сахт; rigid, limited forming

 

Values vary slightly with thickness and standard; confirm tensile and yield on the mill certificate for your gauge.

The small copper addition is what distinguishes 1100 in service.

It gives a modest but useful gain in strength without sacrificing the pure-aluminum forming that lets the sheet be drawn into deep pots and liners, and the metal still anodizes into a uniform, protective film used on trim and nameplates.

1100 thus occupies a deliberate middle ground—not as soft and conductive as 1060, but not as alloyed as 3003, which is why it appears so often in cookware, chemical and general-purpose stock.

Standard Sizes, Surfaces and Weight

1100 sheet is produced from about 0.2 ба 6 мм (plate to 200 mm+ on request), in widths up to roughly 2600 mm and lengths to 12,000 мм. Common sizes include 4×8 ft (1219×2438), 1000×2000, 1220×2440, 1250×2500 and 1500×3000, plus custom blanks to drawing.

Сатҳи / тамом кардан	Истифодаи маъмулӣ
Миллакунӣ (optional PVC/PVDF protective film)	Варақаи умумӣ, захираи истеҳсолӣ, часпидан
Шӯхташуда / оина	Панелҳои ороишӣ, НОММАНҲО, рӯшноӣ
Антидизатсия / ранг карда шудааст	Chemical and outdoor panels, durable signage, тонна
Рӯйдодшуда / circles	Изолятсия, anti-slip, cookware discs and deep-drawn parts

 

Weight is easy at 2.71 г/см³: кг дар як м² = ғафсӣ (мм) × 2.71; a 4×8 ft sheet covers about 2.972 м².

Ғафсӣ	кг / м²	Вазни як варақи 4×8
0.5 мм	1.36	террас. 4.0 кг
1.0 мм	2.71	террас. 8.1 кг
1.5 мм	4.07	террас. 12.1 кг
2.0 мм	5.42	террас. 16.1 кг
3.0 мм	8.13	террас. 24.2 кг

Барномаҳои маъмулӣ

• Chemical process equipment, зарфҳои нигоҳдорӣ, vessels, pipes and fittings that need corrosion resistance and weldability.
• Зинаҳои куки, cooking utensils and deep-drawn or spun parts, plus aluminum circles for pots and pans.
• Гармкунакҳо, инъикоскунандаи чароғҳо, захираи сарпӯши шиша, printing plates and food packaging components.
• Аломатҳо, nameplates and decorative or anodized architectural trim, and general stamped or bent parts.

Fabrication and Surface Treatment

1100 cuts, shears, bends and forms readily and can be laser, plasma or water-jet cut, мӯҳр карда шуд, spun and drilled; it welds cleanly by common processes and takes anodizing, хасу, polishing and coating well.

Use O temper for the deepest draws and harder tempers where the finished part must hold shape; generous bend radii and clean, oil-free surfaces help on high-speed lines.

1100 vs 1050, 1060 ва 3003

Савия	Дин. Ал / хӯлакунонӣ	Қувват	Беҳтарин мувофиқ
1050	99.50% Ал	Паст	Most economical general sheet and cladding
1060	99.60% Ал	Паст	Best conductivity/reflectivity; signs and electrical parts
1100	99.00% Ал, каме Cu	Кам-миёна	Каме қавитар; ташаккул, кафшер, кимиёӣ, Зинаҳои куки
3003	Ал + Мн (дар бораи 1.2%)	Миёна	Дар бораи 20% пурқувват; ошёнаҳо, tread, tougher cladding

 

Интихоб кардан 1100 when you need a little more strength and weldability than 1050/1060 with the same pure-aluminum forming and corrosion; қадам ба боло 3003 for real added strength.

Назорати сифат, Pricing and How to Order

QC covers thickness and flatness, паҳнӣ / дарозӣ ва таҳаммулпазирии диагоналӣ, surface quality and tensile/yield by temper and chemistry on the MTC; ISO 9001 mills support SGS/BV inspection.

Sheet is interleaved with protective film and packed on pallets or in cases with moisture-proof wrapping for export. Pricing follows the aluminum ingot base plus a processing fee, with thinner/wider gauge, custom cutting, surface treatment and small quantities adding cost;

compare per ton and per finished blank on identical specs under FOB/CFR/CIF (маъмулан 30% deposit, balance against the bill of lading). Барои иқтибос, фиристодани хӯла / табъ (1100), цафсӣ, варақ ё андозаҳои холӣ, сатҳи, миқдор, барнома ва бандари таъинот.

Verify new material on production-gauge samples rather than photos: run the sheet through your forming, welding or cutting line at normal speed, ғафсӣ дар саросари паҳнои чен кунед, inspect the surface and, for food or chemical use, confirm the compliance paperwork matches the lot.

A signed pre-production sample then becomes the receiving standard, and an integrated mill that rolls and finishes in-house will hold that standard more reliably across repeat orders than spot resellers.

Саволҳои зуд-зуд додашаванда

С: Чӣ аст 1100 варақи алюминӣ истифода мешавад?

А: Chemical tanks, vessels and piping, cookware and deep-drawn parts, гармӣ, аломатҳо, bottle cap and printing stock, and general fabrication needing formability and corrosion rather than high strength.

С: Чӣ қадар қавӣ аст 1100 нисбат ба 1060 ва 3003?

А: It is slightly stronger than 1050/1060 due to a small copper addition, аммо 3003 (манган) is about 20% пурқувват; H18 1100 reaches roughly 150–200 MPa tensile.

С: Кадом хислатро ман бояд интихоб кунам?

А: O for deep drawing and spinning, H14/H24 for general sheet, H16/H26 for stiffer panels and H18 for the most rigid plate with little forming.

С: What sizes and thicknesses are available?

А: About 0.2–6 mm sheet in widths to roughly 2600 мм, аз ҷумла 4 × 8 фут ва стандартҳои метрӣ, with plate and cut-to-size blanks on request.

С: Can it be welded, anodized and cut to size?

А: Yes—1100 welds cleanly, anodizes and finishes well, and can be laser or sawn cut, bent and supplied as custom blanks with protective film.

С: Як варақи 4×8 чӣ қадар вазн дорад?

А: Тахминан 8.1 кг дар 1 мм, 12.1 кг дар 1.5 мм, 16.1 кг дар 2 мм ва 24.2 кг дар 3 мм, бо истифода аз кг/м² = ғафсӣ (мм) × 2.71 дар болои 2.972 м².

Хулоса

1100 aluminum sheet is the slightly stronger, easy-to-fabricate pure-aluminum plate for chemical equipment, Зинаҳои куки, heat transfer and signs.

Ҳароратро аз рӯи коркарди панел муайян кунед, ғафсӣ ва андозаи буриданро ислоҳ кунед, choose the surface, ва бо сертификатҳои осиёб харед, таҳаммулпазирӣ ва намунаҳои тасдиқшуда на танҳо нарх.