1100 Sheet Aluminium for Sale: Notên, Mezinahî û Rêbernameya Kiryarê
1100 Sheet Aluminium for Sale: Notên, Mezinahî û Rêbernameya Kiryarê
Pêşkêş
1100 aluminum sheet is one of the most practical commercially pure aluminum plates you can buy: with a minimum 99.0% aluminum content and a small copper addition, it is slightly stronger than 1050/1060 while keeping excellent formability, berxwedana korozyonê, weldability and thermal conductivity.
It is the default sheet for chemical equipment, cookware and deep-drawn parts, germê dişewitîne, signs and general fabrication that do not need high strength.
Offered factory-direct, 1100 sheet can be supplied in standard 4×8 ft and metric sizes or cut to your dimensions, with the temper and surface finish the product needs.
This guide covers the composition, milkên, sizes and weights, sepanên, fabrîkî, çawa bi hev re 1050, 1060 û 3003, û meriv çawa ferman dike.
Çi ye 1100 Sheet Aluminium?
1100 is a non-heat-treatable 1xxx-series alloy strengthened only by cold work and softened by annealing. Sheet generally runs about 0.2–6 mm thick (thicker material is plate), supplied flat or cut to length. Awantajên wê yên taybetmend in:
- Ji bo çewisandinê duristbûnek hêja, pûl, spinning û xêzkirina kûr, bi taybetî di tehma O de.
- Very good atmospheric and chemical corrosion resistance from the self-healing oxide film.
- Hêza hinekî bilindtir ji 1050/1060 thanks to a controlled 0.05–0.20% copper addition.
- High thermal and electrical conductivity, plus excellent weldability and easy machining.
- Sivik (ji dor 2.71 g/cm³), rust-free and lower cost than alloyed grades; anodizes to a good film.
- The trade-off is modest strength; load-bearing or wear parts should use 3003, 5052 an 6061.
Pêkhatina Kîmyewî û Taybetmendiyên Mekanîkî
Kîmyaya kontrolkirî (per ASTM B209 / GB/T 3190) keeps silicon plus iron and copper within tight limits so forming, welding and corrosion performance stay high:
| Pêve | Al | Û + Fe | Cu | Mn | Zn |
| 1100 | ≥99.0 | ≤0.95 | 0.05–0.20 | ≤0.05 | ≤0.10 |
Mechanical properties change with temper, ji ber vê yekê heman 1100 pel dikare nerm û kûr-kêşkêş an hişk û hişk were peyda kirin (typical Rm values):
| Bitrî | Tensile (MPa) | Şexsîyet |
| O (Annealed) | biha. 75–110 | Softest; Derketina kûr, spinning, herî zêde formability |
| H12 / H22 | biha. 95–125 | Çaryek dijwar; avakirina ronahiyê |
| H14 / H24 | biha. 110–150 | Nîv-hişk; common general-purpose temper |
| H16 / H26 | biha. 135–170 | Sê çaryek dijwar; panelên hişktir |
| H18 | biha. 150–200 | Tev-hişk; rigid, avakirina sînorkirî |
Nirx li gorî stûrbûn û standard hinekî diguhere; confirm tensile and yield on the mill certificate for your gauge.
The small copper addition is what distinguishes 1100 in service.
It gives a modest but useful gain in strength without sacrificing the pure-aluminum forming that lets the sheet be drawn into deep pots and liners, and the metal still anodizes into a uniform, protective film used on trim and nameplates.
1100 thus occupies a deliberate middle ground—not as soft and conductive as 1060, but not as alloyed as 3003, which is why it appears so often in cookware, chemical and general-purpose stock.
Mezinahiyên Standard, Rû û giranî
1100 pel ji derbar tê hilberandin 0.2 ber 6 mm (plakaya ku 200 mm+ li ser daxwazê), di firehiyên heta bi qasî 2600 mm û dirêjiyên ku 12,000 mm. Common sizes include 4×8 ft (1219×2438), 1000×2000, 1220×2440, 1250×2500 and 1500×3000, plus custom blanks to drawing.
| Rû / qedandin | Bikaranîna tîpîk |
| Mill qedand (optional PVC/PVDF protective film) | Bernameya giştî, stock çêkirinê, qada |
| Brushed / neynik | Panelên xemilandî, Nameprates, biriqîn |
| Anodized kirin / reng-rengkirî | Chemical and outdoor panels, durable signage, trim |
| Embossed / circles | Tenêkirinî, anti-slip, cookware discs and deep-drawn parts |
Weight is easy at 2.71 g/cm³: kg per m² = thickness (mm) × 2.71; a 4×8 ft sheet covers about 2.972 m².
| Qewîtî | kg/m² | Giraniya per 4×8 pel |
| 0.5 mm | 1.36 | biha. 4.0 kg |
| 1.0 mm | 2.71 | biha. 8.1 kg |
| 1.5 mm | 4.07 | biha. 12.1 kg |
| 2.0 mm | 5.42 | biha. 16.1 kg |
| 3.0 mm | 8.13 | biha. 24.2 kg |
Serlêdanên Tîpîkî
- Amûrên pêvajoya kîmyewî, tankên hilanînê, firaxên, pipes and fittings that need corrosion resistance and weldability.
- Cookware, cooking utensils and deep-drawn or spun parts, plus aluminum circles for pots and pans.
- Germbûna germê, refleksên çirayê, stock cap şûşeya, printing plates and food packaging components.
- Nîşan, nameplates and decorative or anodized architectural trim, and general stamped or bent parts.
Fabrication and Surface Treatment
1100 cuts, shears, bends and forms readily and can be laser, plasma or water-jet cut, cîgirtin, spun and drilled; it welds cleanly by common processes and takes anodizing, firçekirin, polishing and coating well.
Use O temper for the deepest draws and harder tempers where the finished part must hold shape; generous bend radii and clean, oil-free surfaces help on high-speed lines.
1100 vs 1050, 1060 û 3003
| Sinif | Min. Al / alloying | Qawet | Best fit |
| 1050 | 99.50% Al | Nizm | Most economical general sheet and cladding |
| 1060 | 99.60% Al | Nizm | Best conductivity/reflectivity; signs and electrical parts |
| 1100 | 99.00% Al, hindik Cu | Kêm-navîn | Hinekî bihêztir; davend, welding, şîmyakî, Cookware |
| 3003 | Al + Mn (ji dor 1.2%) | Medya | Ji dor 20% bihêz; qatan, tread, tougher cladding |
Helbijartin 1100 when you need a little more strength and weldability than 1050/1060 with the same pure-aluminum forming and corrosion; gav avêtin 3003 for real added strength.
Kontrola Kalîteyê, Pricing and How to Order
QC covers thickness and flatness, firehî / dirêj û tolerans diagonal, surface quality and tensile/yield by temper and chemistry on the MTC; ISO 9001 mills support SGS/BV inspection.
Sheet is interleaved with protective film and packed on pallets or in cases with moisture-proof wrapping for export. Biha li pey bingeha lingê aluminiumê û xercek pêvajoyê ye, with thinner/wider gauge, birrîna custom, surface treatment and small quantities adding cost;
compare per ton and per finished blank on identical specs under FOB/CFR/CIF (bi gelemperî 30% diravdan, hevsengiya li dijî fatûreya barkirinê). To quote, alloy / temper şandin (1100), qewîtî, pîvanên pel an vala, rû, jimarî, serîlêdan û porta mebestê.
Verify new material on production-gauge samples rather than photos: run the sheet through your forming, welding or cutting line at normal speed, stûrahiya li seranserê firehiyê bipîve, inspect the surface and, for food or chemical use, confirm the compliance paperwork matches the lot.
A signed pre-production sample then becomes the receiving standard, and an integrated mill that rolls and finishes in-house will hold that standard more reliably across repeat orders than spot resellers.
Pirsên Pir Pir Dipirsin
Q: Çi ye 1100 pelê aluminiumê tê bikaranîn?
YEK: Chemical tanks, vessels and piping, cookware and deep-drawn parts, germê dişewitîne, nîşan, bottle cap and printing stock, and general fabrication needing formability and corrosion rather than high strength.
Q: Çiqas xurt e 1100 danberhev bi 1060 û 3003?
YEK: It is slightly stronger than 1050/1060 due to a small copper addition, lebê 3003 (mangane) is about 20% bihêz; H18 1100 reaches roughly 150–200 MPa tensile.
Q: What temper should I choose?
YEK: O for deep drawing and spinning, H14/H24 for general sheet, H16/H26 for stiffer panels and H18 for the most rigid plate with little forming.
Q: What sizes and thicknesses are available?
YEK: About 0.2–6 mm sheet in widths to roughly 2600 mm, including 4×8 ft and metric standards, with plate and cut-to-size blanks on request.
Q: Can it be welded, anodized and cut to size?
YEK: Yes—1100 welds cleanly, anodizes and finishes well, and can be laser or sawn cut, bent and supplied as custom blanks with protective film.
Q: Çiqas pelê 4×8 giran e?
YEK: Roughly 8.1 kg li 1 mm, 12.1 kg li 1.5 mm, 16.1 kg li 2 mm û 24.2 kg li 3 mm, bikaranîna kg/m² = stûrbûn (mm) × 2.71 ser 2.972 m².
Xelasî
1100 aluminum sheet is the slightly stronger, easy-to-fabricate pure-aluminum plate for chemical equipment, Cookware, heat transfer and signs.
Ji ber ku panel çawa tê pêvajoy kirin germahiya xwe diyar bikin, qalindahî û mezinahiya birrîn rast bikin, choose the surface, û li ser sertîfîkayên mifteyê bikirin, tolerans û nimûneyên pejirandî li şûna bihayê tenê.
