1100 Taratasy Aluminum amidy: naoty, Habe sy Torolàlana ho an'ny mpividy
1100 Taratasy Aluminum amidy: naoty, Habe sy Torolàlana ho an'ny mpividy
Sava lalana
1100 aluminum sheet is one of the most practical commercially pure aluminum plates you can buy: with a minimum 99.0% aluminum content and a small copper addition, it is slightly stronger than 1050/1060 while keeping excellent formability, fanoherana ny harafesina, weldability and thermal conductivity.
It is the default sheet for chemical equipment, cookware and deep-drawn parts, Sinks hafanana, signs and general fabrication that do not need high strength.
Offered factory-direct, 1100 sheet can be supplied in standard 4×8 ft and metric sizes or cut to your dimensions, with the temper and surface finish the product needs.
This guide covers the composition, Properties, sizes and weights, fampiharana, lamba, ahoana ny fampitahana azy 1050, 1060 SY 3003, ary ny fomba hanafatra.
Inona no 1100 Taratasy aluminium?
1100 is a non-heat-treatable 1xxx-series alloy strengthened only by cold work and softened by annealing. Sheet generally runs about 0.2–6 mm thick (thicker material is plate), supplied flat or cut to length. Ny tombony mampiavaka azy dia:
- Ny ductility tsara ho an'ny fiondrika, nohitsakitsahiko, manodina sy manao sary lalina, indrindra amin'ny O.
- Very good atmospheric and chemical corrosion resistance from the self-healing oxide film.
- Somary ambony hery noho ny 1050/1060 thanks to a controlled 0.05–0.20% copper addition.
- High thermal and electrical conductivity, plus excellent weldability and easy machining.
- fahazavana (About 2.71 g/cm³), rust-free and lower cost than alloyed grades; anodizes to a good film.
- The trade-off is modest strength; load-bearing or wear parts should use 3003, 5052 na 6061.
Famoronana simika sy toetra mekanika
Ny simia voafehy (per ASTM B209 / GB / t 3190) keeps silicon plus iron and copper within tight limits so forming, welding and corrosion performance stay high:
| singa | Al | SY + Fe | Cu | Mn | Zn |
| 1100 | ≥99.0 | ≤0.95 | 0.05–0.20 | ≤0.05 | ≤0.10 |
Mechanical properties change with temper, ka mitovy 1100 ny taratasy dia azo omena malefaka sy lalina-drawable na mafy sy henjana (typical Rm values):
| tezitra | Tensile (MPa) | toetra |
| O (annealed) | eo ho eo. 75–110 | malefaka indrindra; sary lalina, kofehy, maximum formability |
| I12 / H22 | eo ho eo. 95–125 | Quarter-hard; hazavana miforona |
| H14 / H24 | eo ho eo. 110-150 | Antsasaky ny henjana; common general-purpose temper |
| H16 / H26 | eo ho eo. 135-170 | Telo ampahefatry ny mafy; tontonana stiffer |
| H18 | eo ho eo. 150-200 | Full-hard; hentitra, miforona voafetra |
Ny sanda dia miovaova kely amin'ny hateviny sy ny fenitra; confirm tensile and yield on the mill certificate for your gauge.
The small copper addition is what distinguishes 1100 in service.
It gives a modest but useful gain in strength without sacrificing the pure-aluminum forming that lets the sheet be drawn into deep pots and liners, and the metal still anodizes into a uniform, protective film used on trim and nameplates.
1100 thus occupies a deliberate middle ground—not as soft and conductive as 1060, but not as alloyed as 3003, which is why it appears so often in cookware, chemical and general-purpose stock.
Habe mahazatra, Surfaces sy lanja
1100 taratasy novokarina avy amin'ny manodidina 0.2 ny 6 MG (takelaka ho 200 mm+ raha angatahina), amin'ny sakany ka hatramin'ny eo ho eo 2600 mm sy ny halavany 12,000 MG. Common sizes include 4×8 ft (1219×2438), 1000×2000, 1220×2440, 1250×2500 and 1500×3000, plus custom blanks to drawing.
| Surface / farany | Fampiasana mahazatra |
| Famaranana Mill (optional PVC/PVDF protective film) | Taratasy ankapobeny, tahiry fanamboarana, clading |
| nisosa / fitaratra | Panel haingon-trano, Nameplates, jiro |
| Anodized / miloko miloko | Chemical and outdoor panels, durable signage, Karakarao tsara |
| Embossed / circles | Insulation, anti-slip, cookware discs and deep-drawn parts |
Weight is easy at 2.71 g/cm³: kg isaky ny m² = hateviny (MG) × 2.71; a 4×8 ft sheet covers about 2.972 m².
| hateviny | kg/m² | Lanja isaky ny takelaka 4 × 8 |
| 0.5 MG | 1.36 | eo ho eo. 4.0 kg |
| 1.0 MG | 2.71 | eo ho eo. 8.1 kg |
| 1.5 MG | 4.07 | eo ho eo. 12.1 kg |
| 2.0 MG | 5.42 | eo ho eo. 16.1 kg |
| 3.0 MG | 8.13 | eo ho eo. 24.2 kg |
Fampiharana mahazatra
- Fitaovana fanodinana simika, tanky fitahirizana, FANAKY, pipes and fittings that need corrosion resistance and weldability.
- Cookware, cooking utensils and deep-drawn or spun parts, plus aluminum circles for pots and pans.
- Milentika ny hafanana, jiro reflectors, stock saron-tavoahangy, printing plates and food packaging components.
- FAMANTARANA, nameplates and decorative or anodized architectural trim, and general stamped or bent parts.
Fabrication and Surface Treatment
1100 cuts, shears, bends and forms readily and can be laser, plasma or water-jet cut, tsy laniny, spun and drilled; it welds cleanly by common processes and takes anodizing, miborosy, polishing and coating well.
Use O temper for the deepest draws and harder tempers where the finished part must hold shape; generous bend radii and clean, oil-free surfaces help on high-speed lines.
1100 vs 1050, 1060 SY 3003
| kilasy | Min. Al / firaka | HERY | Mifanaraka tsara indrindra |
| 1050 | 99.50% Al | IVA | Most economical general sheet and cladding |
| 1060 | 99.60% Al | IVA | Best conductivity/reflectivity; signs and electrical parts |
| 1100 | 99.00% Al, kely Cu | Ambany antonony | Somary matanjaka kokoa; mamorona, welding, simika, Cookware |
| 3003 | Al + Mn (About 1.2%) | SALASALANY | About 20% OANAO; gorodona, tread, tougher cladding |
Mifidiana 1100 when you need a little more strength and weldability than 1050/1060 with the same pure-aluminum forming and corrosion; miakatra mankany 3003 for real added strength.
Fanaraha-maso kalitao, Pricing and How to Order
QC covers thickness and flatness, sakany/lavany ary fandeferana diagonal, surface quality and tensile/yield by temper and chemistry on the MTC; ISO 9001 mills support SGS/BV inspection.
Sheet is interleaved with protective film and packed on pallets or in cases with moisture-proof wrapping for export. Ny vidiny dia manaraka ny fototra aluminium ingot miampy ny sara fanodinana, with thinner/wider gauge, fanapahana manokana, fitsaboana ambonin'ny sy ny fatra kely manampy ny vidiny;
compare per ton and per finished blank on identical specs under FOB/CFR/CIF (mahazatra 30% petra-bola, fifandanjana amin'ny volavolan-dalàna). Manonona, mandefa alloy/temper (1100), hateviny, takelaka na refy banga, surface, habetsahana, fampiharana sy seranan-tsambo.
Verify new material on production-gauge samples rather than photos: run the sheet through your forming, welding or cutting line at normal speed, mandrefy ny hateviny manerana ny sakany, inspect the surface and, for food or chemical use, confirm the compliance paperwork matches the lot.
A signed pre-production sample then becomes the receiving standard, and an integrated mill that rolls and finishes in-house will hold that standard more reliably across repeat orders than spot resellers.
Fanontaniana matetika
Q: Inona ny 1100 sheet aluminium ampiasaina?
ny: Chemical tanks, vessels and piping, cookware and deep-drawn parts, Sinks hafanana, FAMANTARANA, bottle cap and printing stock, and general fabrication needing formability and corrosion rather than high strength.
Q: Hatraiza ny? 1100 raha oharina amin'ny 1060 SY 3003?
ny: It is slightly stronger than 1050/1060 due to a small copper addition, SAINGY 3003 (manganese) is about 20% OANAO; H18 1100 reaches roughly 150–200 MPa tensile.
Q: Inona no toetra tokony hofidiko?
ny: O for deep drawing and spinning, H14/H24 for general sheet, H16/H26 for stiffer panels and H18 for the most rigid plate with little forming.
Q: What sizes and thicknesses are available?
ny: About 0.2–6 mm sheet in widths to roughly 2600 MG, ao anatin'izany ny fenitra 4 × 8 ft sy metrika, with plate and cut-to-size blanks on request.
Q: Can it be welded, anodized and cut to size?
ny: Yes—1100 welds cleanly, anodizes and finishes well, and can be laser or sawn cut, bent and supplied as custom blanks with protective film.
Q: Ohatrinona ny lanjan'ny taratasy 4×8?
ny: Manodidina 8.1 kg ao 1 MG, 12.1 kg ao 1.5 MG, 16.1 kg ao 2 mm ary 24.2 kg ao 3 MG, mampiasa kg/m² = hateviny (MG) × 2.71 TAPITRA 2.972 m².
Famaranana
1100 aluminum sheet is the slightly stronger, easy-to-fabricate pure-aluminum plate for chemical equipment, Cookware, heat transfer and signs.
Lazao ny hafanana amin'ny fomba fikarakarana ny tontonana, amboary ny hateviny sy ny habeny tapaka, choose the surface, ary mividy amin'ny taratasy fanamarinana fikosoham-bary, fandeferana sy santionany nankatoavina fa tsy ny vidiny fotsiny.
