1100 Ibinebenta ang Aluminum Sheet: Mga grado, Mga Sukat at Gabay ng Mamimili
1100 Ibinebenta ang Aluminum Sheet: Mga grado, Mga Sukat at Gabay ng Mamimili
Panimula
1100 aluminum sheet is one of the most practical commercially pure aluminum plates you can buy: with a minimum 99.0% aluminum content and a small copper addition, it is slightly stronger than 1050/1060 while keeping excellent formability, paglaban sa kaagnasan, weldability and thermal conductivity.
It is the default sheet for chemical equipment, cookware and deep-drawn parts, Heat sink, signs and general fabrication that do not need high strength.
Offered factory-direct, 1100 sheet can be supplied in standard 4×8 ft and metric sizes or cut to your dimensions, with the temper and surface finish the product needs.
This guide covers the composition, mga pag -aari, sizes and weights, mga aplikasyon, katha, kung paano ito inihambing sa 1050, 1060 at 3003, at kung paano mag-order.
Ano ba 1100 Aluminum Sheet?
1100 is a non-heat-treatable 1xxx-series alloy strengthened only by cold work and softened by annealing. Sheet generally runs about 0.2–6 mm thick (thicker material is plate), supplied flat or cut to length. Ang mga katangiang bentahe nito ay:
- Napakahusay na kalagkitan para sa baluktot, Stamping, umiikot at malalim na pagguhit, lalo na sa O init ng ulo.
- Very good atmospheric and chemical corrosion resistance from the self-healing oxide film.
- Bahagyang mas mataas ang lakas kaysa 1050/1060 thanks to a controlled 0.05–0.20% copper addition.
- High thermal and electrical conductivity, plus excellent weldability and easy machining.
- Magaan (tungkol sa 2.71 g/cm³), rust-free and lower cost than alloyed grades; anodizes to a good film.
- The trade-off is modest strength; load-bearing or wear parts should use 3003, 5052 o 6061.
Komposisyon ng Kemikal at Mga Katangiang Mekanikal
Ang kinokontrol na kimika (per ASTM B209 / GB/T. 3190) keeps silicon plus iron and copper within tight limits so forming, welding and corrosion performance stay high:
| Elemento | Sinabi ni Al | At + Fe | Cu | Mn | Zn |
| 1100 | ≥99.0 | ≤0.95 | 0.05–0.20 | ≤0.05 | ≤0.10 |
Mechanical properties change with temper, kaya pareho 1100 sheet ay maaaring ibigay malambot at malalim-drawable o matigas at matibay (typical Rm values):
| init ng ulo | Makunat (MPa) | karakter |
| O (Annealed) | tinatayang. 75–110 | Pinakamalambot; malalim na pagguhit, umiikot, maximum formability |
| H12 / H22 | tinatayang. 95–125 | Quarter-hard; liwanag na bumubuo |
| H14 / H24 | tinatayang. 110–150 | Half-hard; common general-purpose temper |
| H16 / H26 | tinatayang. 135–170 | Three-quarter-hard; mas matigas na mga panel |
| H18 | tinatayang. 150–200 | Buong-hirap; matigas, limitadong pagbubuo |
Ang mga halaga ay bahagyang nag-iiba sa kapal at pamantayan; confirm tensile and yield on the mill certificate for your gauge.
The small copper addition is what distinguishes 1100 in service.
It gives a modest but useful gain in strength without sacrificing the pure-aluminum forming that lets the sheet be drawn into deep pots and liners, and the metal still anodizes into a uniform, protective film used on trim and nameplates.
1100 thus occupies a deliberate middle ground—not as soft and conductive as 1060, but not as alloyed as 3003, which is why it appears so often in cookware, chemical and general-purpose stock.
Mga Karaniwang Sukat, Ibabaw at Timbang
1100 sheet ay ginawa mula sa tungkol sa 0.2 sa 6 mm (plato sa 200 mm+ kapag hiniling), sa lapad hanggang halos 2600 mm at haba hanggang 12,000 mm. Common sizes include 4×8 ft (1219×2438), 1000×2000, 1220×2440, 1250×2500 and 1500×3000, plus custom blanks to drawing.
| Ibabaw / Tapusin | Karaniwang gamit |
| Tapos na ang Mill (optional PVC/PVDF protective film) | Pangkalahatang sheet, stock ng katha, cladding |
| Nagsipilyo / salamin | Mga panel na pampalamuti, nameplate, ilaw |
| Anodized / pinahiran ng kulay | Chemical and outdoor panels, durable signage, trim |
| Embossed / circles | Pagkakabukod, anti-slip, cookware discs and deep-drawn parts |
Weight is easy at 2.71 g/cm³: kg bawat m² = kapal (mm) × 2.71; a 4×8 ft sheet covers about 2.972 m².
| kapal | kg/m² | Timbang bawat 4×8 sheet |
| 0.5 mm | 1.36 | tinatayang. 4.0 kg |
| 1.0 mm | 2.71 | tinatayang. 8.1 kg |
| 1.5 mm | 4.07 | tinatayang. 12.1 kg |
| 2.0 mm | 5.42 | tinatayang. 16.1 kg |
| 3.0 mm | 8.13 | tinatayang. 24.2 kg |
Karaniwang mga aplikasyon
- Mga kagamitan sa proseso ng kemikal, Mga tanke ng imbakan, mga sisidlan, pipes and fittings that need corrosion resistance and weldability.
- Cookware, cooking utensils and deep-drawn or spun parts, plus aluminum circles for pots and pans.
- Heat sink, mga reflector ng lampara, stock ng takip ng bote, printing plates and food packaging components.
- Mga palatandaan, nameplates and decorative or anodized architectural trim, and general stamped or bent parts.
Fabrication and Surface Treatment
1100 cuts, shears, bends and forms readily and can be laser, plasma or water-jet cut, naselyohang, spun and drilled; it welds cleanly by common processes and takes anodizing, brushing, polishing and coating well.
Use O temper for the deepest draws and harder tempers where the finished part must hold shape; generous bend radii and clean, oil-free surfaces help on high-speed lines.
1100 vs. 1050, 1060 at 3003
| Grado | Min. Sinabi ni Al / Alloying | Lakas | Pinakamahusay na akma |
| 1050 | 99.50% Sinabi ni Al | Mababa | Most economical general sheet and cladding |
| 1060 | 99.60% Sinabi ni Al | Mababa | Best conductivity/reflectivity; signs and electrical parts |
| 1100 | 99.00% Sinabi ni Al, isang maliit na Cu | Low-medium | Medyo malakas; bumubuo, Pag -welding, kemikal, Cookware |
| 3003 | Sinabi ni Al + Mn (tungkol sa 1.2%) | Katamtaman | Tungkol sa 20% mas malakas; mga sahig, tread, tougher cladding |
Piliin 1100 when you need a little more strength and weldability than 1050/1060 with the same pure-aluminum forming and corrosion; hakbang hanggang sa 3003 for real added strength.
KONTROL CONTROL, Pricing and How to Order
QC covers thickness and flatness, lapad/haba at diagonal tolerance, surface quality and tensile/yield by temper and chemistry on the MTC; ISO 9001 mills support SGS/BV inspection.
Sheet is interleaved with protective film and packed on pallets or in cases with moisture-proof wrapping for export. Ang pagpepresyo ay sumusunod sa aluminum ingot base kasama ang bayad sa pagproseso, with thinner/wider gauge, custom cutting, surface treatment and small quantities adding cost;
compare per ton and per finished blank on identical specs under FOB/CFR/CIF (karaniwan 30% deposito, balanse laban sa bill of lading). Upang quote, magpadala ng haluang metal / init ng ulo (1100), kapal, sheet o blangko na sukat, ibabaw, dami, application at destination port.
Verify new material on production-gauge samples rather than photos: run the sheet through your forming, welding or cutting line at normal speed, sukatin ang kapal sa buong lapad, inspect the surface and, for food or chemical use, confirm the compliance paperwork matches the lot.
A signed pre-production sample then becomes the receiving standard, and an integrated mill that rolls and finishes in-house will hold that standard more reliably across repeat orders than spot resellers.
Madalas na nagtanong
Q: Ano ang 1100 Ang sheet ng aluminyo na ginamit para sa?
A: Chemical tanks, vessels and piping, cookware and deep-drawn parts, Heat sink, Mga palatandaan, bottle cap and printing stock, and general fabrication needing formability and corrosion rather than high strength.
Q: Gaano katindi ang 1100 kumpara sa 1060 at 3003?
A: It is slightly stronger than 1050/1060 due to a small copper addition, ngunit 3003 (mangganeso) is about 20% mas malakas; H18 1100 reaches roughly 150–200 MPa tensile.
Q: What temper should I choose?
A: O for deep drawing and spinning, H14/H24 for general sheet, H16/H26 for stiffer panels and H18 for the most rigid plate with little forming.
Q: What sizes and thicknesses are available?
A: About 0.2–6 mm sheet in widths to roughly 2600 mm, kabilang ang 4×8 ft at metric standards, with plate and cut-to-size blanks on request.
Q: Can it be welded, anodized and cut to size?
A: Yes—1100 welds cleanly, anodizes and finishes well, and can be laser or sawn cut, bent and supplied as custom blanks with protective film.
Q: Magkano ang bigat ng isang 4×8 sheet?
A: Humigit -kumulang 8.1 kg sa 1 mm, 12.1 kg sa 1.5 mm, 16.1 kg sa 2 mm at 24.2 kg sa 3 mm, gamit ang kg/m² = kapal (mm) × 2.71 higit sa 2.972 m².
Konklusyon
1100 aluminum sheet is the slightly stronger, easy-to-fabricate pure-aluminum plate for chemical equipment, Cookware, heat transfer and signs.
Tukuyin ang init ng ulo mula sa kung paano pinoproseso ang panel, ayusin ang kapal at sukat ng hiwa, choose the surface, at bumili sa mga sertipiko ng gilingan, tolerances at aprubadong mga sample sa halip na presyo lamang.
