Gelenek 1060 Alüminyum levha: Notlar, Öfkeler, Boyutlar ve Satın Alma Kılavuzu

giriiş

Gelenek 1060 aluminum sheet is one of the most widely ordered commercially pure aluminum plates in the world.

As a 1xxx-series grade with a minimum 99.60% aluminum content, 1060 combines excellent formability, korozyon direnci, electrical and thermal conductivity and weldability with a low, stable price

—which makes it the default choice for signage, building cladding, insulation jacketing, lamp reflectors, ısı yutucular, stamping and deep-drawn parts that do not need high strength.

Ordering it as a “custom” product means fixing the temper, kalınlık, sheet size, surface finish and cut dimensions to your product rather than accepting stock plate.

This short guide covers the composition and mechanical properties of 1060, how to choose the temper, standard sizes and weights, tipik uygulamalar, how it compares with 1050, 1100 Ve 3003, and what to specify when ordering factory-direct.

Nedir 1060 Alüminyum levha?

1060 is a non-heat-treatable commercially pure aluminum; it is strengthened only by cold working and softened by annealing. Sheet generally runs from about 0.2 ile 6 mm kalınlığında (thicker material is classed as plate), supplied flat or in cut-to-length panels. Its characteristic advantages are:

• Excellent ductility for bending, damgalama, spinning and deep drawing, especially in the O temper.
• Very good atmospheric corrosion resistance from the natural oxide film, ideal for outdoor signage and insulation jacketing.
• High electrical and thermal conductivity, suited to busbars, battery connectors, reflectors and heat-spreading parts.
• Excellent weldability and easy machining, cutting and anodizing.
• Düşük yoğunluklu (hakkında 2.71 g/cm³) for light, rust-free panels, at a lower cost than alloyed grades.
• The trade-off is low mechanical strength; load-bearing or high-wear parts should use 3003, 5052 veya 6061 yerine.

Composition and Mechanical Properties

The controlled chemistry (GB/T için 3190, ağırlık %) keeps iron and silicon low so conductivity and corrosion resistance stay high:

eleman	Al	Ve	Fe	cu	Mn	Mg	Zn	İle ilgili
1060	≥99,60	≤0,25	≤0,35	≤0,05	≤0,03	≤0,03	≤0,05	≤0,03

 

Mechanical properties change sharply with temper, so the same 1060 sheet can be supplied soft and deep-drawable or hard and rigid:

Öfke	Gerilme direnci (MPa)	Uzama	Karakter
Ö (tavlanmış)	yaklaşık. 60–100	25–@	En yumuşak; derin çizim, eğirme, maksimum şekillendirilebilirlik
H12 / H22	yaklaşık. 75–115	10–20%	Quarter-hard; light forming
H14 / H24	yaklaşık. 95–135	6–	Yarı sert; the common general-purpose and sign temper
H16 / H26	yaklaşık. 120–160	3–10%	Three-quarter-hard; stiffer panels
H18	yaklaşık. 160–190	2–%8	Tam sert; rigid, limited forming

 

Values vary slightly with thickness and standard; always confirm the tensile and yield range on the mill certificate for your gauge.

Standard Sizes, Surfaces and Weight

1060 sheet is produced from about 0.2 ile 6 mm (plate to 200 mm+ on request), in widths up to roughly 2600 mm and lengths to 12,000 mm. Common stock and cut sizes include 4×8 ft (1219×2438 mm), 4×10 ft, 1000×2000, 1220×2440, 1250×2500 and 1500×3000 mm, plus fully custom blanks cut to your drawing.

Yüzey / sona ermek	Tipik kullanım
Değirmen bitişi (with optional PVC/PVDF protective film)	General sheet, kaplama, fabrication stock
Fırçalanmış / hairline or mirror-polished	Decorative panels, isim levhaları, aydınlatma
Anodized or color-coated (PVDF/PE)	Curtain wall, çatı kaplama, durable outdoor signage
Embossed stucco / five-bar tread	Insulation jacketing, anti-slip and decorative sheet

 

Weight is easy to calculate at a density of 2.71 g/cm³: kg per m² = thickness (mm) × 2.71. A 4×8 ft sheet covers about 2.972 m².

Kalınlık	kg/m²	Weight per 4×8 sheet
0.5 mm	1.36	yaklaşık. 4.0 kilogram
1.0 mm	2.71	yaklaşık. 8.1 kilogram
1.5 mm	4.07	yaklaşık. 12.1 kilogram
2.0 mm	5.42	yaklaşık. 16.1 kilogram
3.0 mm	8.13	yaklaşık. 24.2 kilogram

 

Tipik Uygulamalar

• Tabela, yol işaretleri, nameplates and advertising boards – usually H14/H18 sheet that prints, anodizes and vinyl-mounts cleanly.
• Building curtain wall, çatı kaplama, ceiling and decorative panels, often anodized or color-coated.
• Anti-corrosion insulation jacketing (aluminum cladding) for pipes, tanks and ducting, frequently stucco-embossed and in H14/H16.
• Lamp reflectors, lighting parts, heat sinks and radiator components, plus battery flexible connectors and conductive parts.
• Tencere, lamp shells and deep-drawn or spun parts in soft O temper, plus general stamping, bending and laser-cut blanks.

1060 vs 1050, 1100 Ve 3003

Seviye	Min.. Al / alaşımlama	Kuvvet	Best fit
1050	99.50% Al	Düşük	Most economical general sheet, cladding and insulation
1060	99.60% Al	Düşük	Signs, conductive and reflective parts; better conductivity than 1050
1100	99.00% Al, a little Cu	Low-medium	Biraz daha güçlü; şekillendirme, kaynak, kimyasal ekipman, tencere
3003	Al + Mn (hakkında 1.2%)	Orta	Hakkında 20% daha güçlü, better for floors, tread plate and tougher cladding

 

Seçmek 1060 when purity, iletkenlik, reflectivity or price leads and strength is not critical; step up to 1100 for a little more strength and weldability, ve 3003 (veya 5052/6061) for load-bearing, abrasion or structural duty.

Custom Options, Quality Control and Ordering

A custom 1060 order can specify temper (Ö, H12/H14/H16/H18 or H22/H24/H26), thickness and tolerance, sheet or blank dimensions, edge type (slit or sawn), yüzey, protective film, anodizing/coating color, embossing and packaging. Fabrication services often include laser, plasma or water-jet cutting, bükme, punching, drilling and CNC blanks made to drawing.

Quality control covers thickness and flatness, width/length and diagonal tolerance, yüzey kalitesi (çizik yok, lekeler, oil or roll marks on critical faces), tensile properties by temper and alloy chemistry on the mill test certificate;

ISO 9001 mills support SGS/BV/TUV inspection. Sheets are normally interleaved with protective film, packed on wooden pallets or in wooden cases with moisture-proof wrapping for export.

Pricing follows the aluminum ingot base plus a processing fee, with thinner or wider gauge, custom cutting, surface treatment and small quantities adding cost; compare suppliers per ton and per finished blank on identical temper, ölçer, size and finish, under FOB/CFR/CIF terms (yaygın olarak 30% deposit with balance against the bill of lading).

Sık sorulan sorular

Q: What is custom 1060 için kullanılan alüminyum levha?

A: İşaretler ve isim levhaları, building cladding and roofing, pipe/tank insulation jacketing, reflektörler, ısı yutucular, conductive parts, cookware and stamped, spun or deep-drawn components that need formability and corrosion resistance rather than high strength.

Q: What temper should I choose?

A: Use O for deep drawing and spinning, H14/H24 for general sheet and signage, H16/H26 for stiffer panels and H18 for the flattest, most rigid sheet with little forming.

Q: What thicknesses and sizes are available?

A: Common sheet runs 0.2–6 mm in widths up to about 2600 mm, including 4×8 ft and metric standards, with plate and fully custom cut-to-size blanks on request.

Q: How much does a 4×8 sheet weigh?

A: Kabaca 8.1 kg at 1 mm, 12.1 kg at 1.5 mm, 16.1 kg at 2 mm ve 24.2 kg at 3 mm, using kg/m² = thickness (mm) × 2.71 üzerinde 2.972 m².

Q: 1060 vs 3003 sheet – which do I need?

A: 1060 for economy, conductivity and corrosion resistance in light-duty work; 3003 when you need about 20% more strength for floors, basamak plakası, roofing or tougher formed parts.

Q: Can it be anodized, coated and cut to size?

A: Evet. 1060 anodizes well and can be brushed, mirror-polished, color-coated, embossed and supplied with protective film, plus laser-cut, bent or CNC-fabricated to your drawing.

Çözüm

Gelenek 1060 aluminum sheet is the economical, easy-to-fabricate pure-aluminum workhorse for signage, kaplama, yalıtım, reflectors and formed parts.

Specify the temper from how the panel is processed (O for deep forming, H14/H24 for general and sign use, H18 for rigidity), fix thickness and cut size, choose the surface finish, and buy on mill certificates, dimensional tolerances and approved samples rather than price alone.