Maxsus 1060 Alyuminiy varaq: Grades, Templar, Sizes and Buyer’s Guide
Maxsus 1060 Alyuminiy varaq: Grades, Templar, Sizes and Buyer’s Guide
Kirish
Maxsus 1060 aluminum sheet is one of the most widely ordered commercially pure aluminum plates in the world.
As a 1xxx-series grade with a minimum 99.60% aluminum content, 1060 combines excellent formability, korroziyaga qarshilik, electrical and thermal conductivity and weldability with a low, stable price
—which makes it the default choice for signage, building cladding, insulation jacketing, lamp reflectors, issiqlik qabul qiluvchilar, stamping and deep-drawn parts that do not need high strength.
Ordering it as a “custom” product means fixing the temper, qalinligi, sheet size, surface finish and cut dimensions to your product rather than accepting stock plate.
This short guide covers the composition and mechanical properties of 1060, how to choose the temper, standard sizes and weights, odatiy ilovalar, how it compares with 1050, 1100 va 3003, and what to specify when ordering factory-direct.
Nima 1060 Alyuminiy varaq?
1060 is a non-heat-treatable commercially pure aluminum; it is strengthened only by cold working and softened by annealing. Sheet generally runs from about 0.2 uchun 6 mm qalinligi (thicker material is classed as plate), supplied flat or in cut-to-length panels. Its characteristic advantages are:
- Excellent ductility for bending, shtamplash, spinning and deep drawing, especially in the O temper.
- Very good atmospheric corrosion resistance from the natural oxide film, ideal for outdoor signage and insulation jacketing.
- High electrical and thermal conductivity, suited to busbars, battery connectors, reflectors and heat-spreading parts.
- Excellent weldability and easy machining, cutting and anodizing.
- Kam zichlik (haqida 2.71 g/sm³) for light, rust-free panels, at a lower cost than alloyed grades.
- The trade-off is low mechanical strength; load-bearing or high-wear parts should use 3003, 5052 yoki 6061 o'rniga.
Composition and Mechanical Properties
The controlled chemistry (GB/T uchun 3190, vazn %) keeps iron and silicon low so conductivity and corrosion resistance stay high:
| Element | Al | Va | Fe | Cu | Mn | Mg | Zn | Of |
| 1060 | ≥99,60 | ≤0.25 | ≤0.35 | ≤0.05 | ≤0.03 | ≤0.03 | ≤0.05 | ≤0.03 |
Mechanical properties change sharply with temper, so the same 1060 varaq yumshoq va chuqur tortiladigan yoki qattiq va qattiq bo'lishi mumkin:
| Jahl | Mustahkamlik chegarasi (MPa) | Cho'zilish | Xarakter |
| O (tavlangan) | taxminan. 60-100 | 25-40% | Eng yumshoq; chuqur chizish, yigiruv, maksimal shakllanish qobiliyati |
| H12 / H22 | taxminan. 75-115 | 10-20% | Chorak qiyin; yorug'likni shakllantirish |
| H14 / H24 | taxminan. 95-135 | 6-15% | Yarim qattiq; umumiy umumiy maqsad va belgi temperli |
| H16 / H26 | taxminan. 120-160 | 3-10% | Uch chorak qiyin; qattiqroq panellar |
| H18 | taxminan. 160-190 | 2-8% | To'liq-qattiq; qattiq, cheklangan shakllanish |
Qalinligi va standarti bo'yicha qiymatlar biroz farq qiladi; har doim o'lchagichingiz uchun tegirmon sertifikatida tortish va rentabellik oralig'ini tasdiqlang.
Standart o'lchamlar, Yuzaki va og'irligi
1060 varaq taxminan ishlab chiqariladi 0.2 uchun 6 mm (plastinka uchun 200 so'rov bo'yicha mm+), kengligida taxminan 2600 mm va uzunliklar uchun 12,000 mm. Umumiy stok va kesish o'lchamlari 4 × 8 futni o'z ichiga oladi (1219×2438 mm), 4×10 fut, 1000×2000, 1220×2440, 1250×2500 and 1500×3000 mm, plus fully custom blanks cut to your drawing.
| Yuzaki / tugatish | Oddiy foydalanish |
| Tegirmonni tugatish (with optional PVC/PVDF protective film) | General sheet, qoplama, fabrication stock |
| Cho'tkasi / hairline or mirror-polished | Decorative panels, oqsoqollar, yoritish |
| Anodized or color-coated (PVDF/PE) | Curtain wall, Tom yopish, durable outdoor signage |
| Embossed stucco / five-bar tread | Insulation jacketing, anti-slip and decorative sheet |
Weight is easy to calculate at a density of 2.71 g/sm³: kg per m² = thickness (mm) × 2.71. A 4×8 ft sheet covers about 2.972 m².
| Qalinligi | kg/m² | Weight per 4×8 sheet |
| 0.5 mm | 1.36 | taxminan. 4.0 kg |
| 1.0 mm | 2.71 | taxminan. 8.1 kg |
| 1.5 mm | 4.07 | taxminan. 12.1 kg |
| 2.0 mm | 5.42 | taxminan. 16.1 kg |
| 3.0 mm | 8.13 | taxminan. 24.2 kg |
Odatda arizalar
- Belgi, yo'l belgilari, nameplates and advertising boards – usually H14/H18 sheet that prints, anodizes and vinyl-mounts cleanly.
- Building curtain wall, Tom yopish, ceiling and decorative panels, often anodized or color-coated.
- Anti-corrosion insulation jacketing (aluminum cladding) for pipes, tanks and ducting, frequently stucco-embossed and in H14/H16.
- Lamp reflectors, lighting parts, heat sinks and radiator components, plus battery flexible connectors and conductive parts.
- Kostryulkalar, lamp shells and deep-drawn or spun parts in soft O temper, plus general stamping, bükme va lazer bilan kesilgan blankalar.
1060 va boshqalar 1050, 1100 va 3003
| Baho | Min. Al / qotishma | Kuch | Eng yaxshi mos |
| 1050 | 99.50% Al | Past | Eng iqtisodiy umumiy varaq, qoplama va izolyatsiya |
| 1060 | 99.60% Al | Past | Belgilar, Supero'tkazuvchilar va aks ettiruvchi qismlar; nisbatan yaxshiroq o'tkazuvchanlik 1050 |
| 1100 | 99.00% Al, bir oz Cu | Past-o'rta | Bir oz kuchliroq; shakllantirish, payvandlash, kimyoviy uskunalar, kostryulkalar |
| 3003 | Al + Mn (haqida 1.2%) | O'rta | Haqida 20% kuchli, pollar uchun yaxshiroqdir, protektor plitasi va qattiqroq qoplama |
Tanlang 1060 poklik bo'lganda, o'tkazuvchanlik, aks ettirish yoki narx etakchilik va kuch muhim emas; gacha qadam tashlang 1100 bir oz ko'proq quvvat va payvandlanish uchun, va uchun 3003 (yoki 5052/6061) yuk ko'tarish uchun, aşınma yoki strukturaviy vazifa.
Maxsus parametrlar, Sifat nazorati va buyurtma
Odat 1060 order can specify temper (O, H12/H14/H16/H18 or H22/H24/H26), thickness and tolerance, sheet or blank dimensions, edge type (slit or sawn), sirtni tugatish, protective film, anodizing/coating color, embossing and packaging. Fabrication services often include laser, plasma or water-jet cutting, egiluvchan, punching, drilling and CNC blanks made to drawing.
Quality control covers thickness and flatness, width/length and diagonal tolerance, sirt sifati (tirnalish yo'q, dog'lar, oil or roll marks on critical faces), tegirmon sinov sertifikatida temper va qotishma kimyo bo'yicha valentlik xususiyatlari;
ISO 9001 tegirmonlar SGS/BV/TUV tekshiruvini qo'llab-quvvatlaydi. Plitalar odatda himoya plyonka bilan qoplangan, eksport uchun yog'och tagliklarga yoki namlik o'tkazmaydigan o'ralgan yog'och qutilarga qadoqlangan.
Narxlar alyuminiy quyma bazasiga va qayta ishlash to'loviga mos keladi, yupqaroq yoki kengroq o'lchov bilan, moslashtirilgan kesish, sirtni qayta ishlash va kichik miqdorlar qo'shimcha xarajatlar; Yetkazib beruvchilarni tonnaga va tayyor blankaga bir xil temperamentda solishtiring, o'lchagich, hajmi va tugatish, FOB/CFR/CIF shartlariga muvofiq (odatda 30% deposit with balance against the bill of lading).
Tez-tez so'raladigan savollar
Sh: What is custom 1060 uchun alyuminiy qatlam ishlatiladi?
A: Belgilar va belgilar, building cladding and roofing, pipe/tank insulation jacketing, ma'rifiy, issiqlik qabul qiluvchilar, conductive parts, cookware and stamped, spun or deep-drawn components that need formability and corrosion resistance rather than high strength.
Sh: What temper should I choose?
A: Use O for deep drawing and spinning, H14/H24 for general sheet and signage, H16/H26 for stiffer panels and H18 for the flattest, most rigid sheet with little forming.
Sh: What thicknesses and sizes are available?
A: Common sheet runs 0.2–6 mm in widths up to about 2600 mm, including 4×8 ft and metric standards, with plate and fully custom cut-to-size blanks on request.
Sh: How much does a 4×8 sheet weigh?
A: Taxminan 8.1 kg at 1 mm, 12.1 kg at 1.5 mm, 16.1 kg at 2 mm va 24.2 kg at 3 mm, using kg/m² = thickness (mm) × 2.71 ustida 2.972 m².
Sh: 1060 va boshqalar 3003 sheet – which do I need?
A: 1060 for economy, conductivity and corrosion resistance in light-duty work; 3003 when you need about 20% more strength for floors, taglik plitasi, roofing or tougher formed parts.
Sh: Can it be anodized, coated and cut to size?
A: Ha. 1060 anodizes well and can be brushed, mirror-polished, color-coated, embossed and supplied with protective film, plus laser-cut, bent or CNC-fabricated to your drawing.
Xulosa
Maxsus 1060 aluminum sheet is the economical, easy-to-fabricate pure-aluminum workhorse for signage, qoplama, izolyatsiya, reflectors and formed parts.
Specify the temper from how the panel is processed (O for deep forming, H14/H24 for general and sign use, H18 for rigidity), fix thickness and cut size, choose the surface finish, and buy on mill certificates, dimensional tolerances and approved samples rather than price alone.
